227128-1-M-GE-WB04T10011-Burner-Gasket.jpg
227128-1-S-GE-WB04T10011-Burner-Gasket.jpg 227128-2-S-GE-WB04T10011-Burner-Gasket.jpg

Burner Gasket

PartSelect Number PS227128

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $4.51
  • You Save

    $.75
  • Your Price

    $3.76
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Burner Gasket

Part Number 232502

$4.21
In Stock

Burner Gasket

Part Number 227129

$6.24
In Stock

Burner Gasket

Part Number 227131

$7.05
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 3 reviews What's this?
1-3 of 3
 

17 of 25 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerMichael from Weatogue CT

No spark at one burner

Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner casting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

Customerfrank from cathedral city CA

Igniter wasn't lighting burner

Repair to range went real well, Lifted range from

counter. Removed eight screws that secure burner

assembly. Lifted burners from it's position, and

removed igniters. Installed heat srink at burner

connections so as to ensure high voltage would

have no leaks. Removed insulation, and installed

spark module.. Reassembled unit, placed in

counter cut out, put 110 volt cord into outlet.

Tested all burners, everything worked great..

The repair took about hour and 15 minutes.

Have fun and be careful...... THE END

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Burner Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDavid A from Spring TX

Burner would not light because spark was skiping to ground elsewhere

First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3