| |
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerLynne from Weatherford OK
My old knobs were so worn that I couldn't see the numbers
I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDave from Bloomingburg NY
Knobs were getting hard to read.
Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWALTER from EL CAJON CA
Old nkobs old and discolored
took old knobs off replaced in 3 minutes
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerRoyal from Gilmer TX
Burner would not get hot
removed two screws thenpulled element up unpluged wires
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerAnne from Bedford Hills, NY
Could not use one burner
TURNED POWER TO STOVE OFF. REMOVED TWO SCREWS FROM COVER - LIFTED COVER UP AND PULLED SWITCH OUT AND DISCONNECTED WIRES. PUT NEW SWITCH IN AND CONNECTED WIRES. MADE SURE THAT IT WAS IN CORRECT POSITION BY PLACING KNOB ON TO MAKE SURE OFF POSITION WAS CORRECT - THEN PLACED PLATE IN POSITION AND CLOSED - PUT TWO SCREWS BACK ON PLATE AND PUT NEW KNOB ON. TURNED POWER BACK ON AND TURNED KNOB AND BURNER BACK IN OPERATION
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerArthur H from Irving TX
Surface switch was bad
just swapped out the two switches
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSabra from Dallas TX
Lost one of the knobs
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from Flippin AR
Over the years the numbers has worn off the knobs.
Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerEllery from Hammond LA
|
2 of 6 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerRichard W. from Clifton VA
Switch didn't work & knobs and escuthion worn
Thru the circuit braker for the unit. Removed 2 screws on the escuthion, removed the nuts holding the escuthion to the knobs, rplaced switch, escuthiuon, pilot light fixtures were defective so ordered some for overnight shipment. Pilot light fixtures were a little difficult but soon went together. Wired everthing up, screwed new estcuhion in place. Wow, looked like a new unit w/ new escuthion and knobs rather than a 20 year old unit. Thru circuit breaker on and nothing happend, no power to unit. Couldn't figure out problem for several hours. In despiration called and made a service appointment. Couple of hours later was rechecking circuit breaker because other outlers in kitchen didn't work either. Discovered I had thrown the circuit breaker for the oven rather than drop in stove unit. Tripped that circuit and ev erything worked like a champ. Cancelled service appointment and had a small "celibration".
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
Tools
CustomerLenice from Stuart FL
Elec. Stove-top knobs (imprinted with hi to lo numbers 1 to 10)worn to non-readable.
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from Bossier City LA
New filter & new knobs
Simply replaced these items with no difficulty. John LeGrand
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from Meredith NH
Knobs sloppy and discolored and filter bent
This has been a wonderful cooktop and I could only hope todays quality is equally as good but after 25 yrs. I doubt it especially after looking at new dishwashers in the last couple of days. too sad. but these repairs were minor and no trouble. what amazed me most was ordering one afternoon and the parts were here the following day ! great service
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDenise from Huntington NY
Knobs were worn and illegible
Removed the old ones and snapped on the new.
It was a snap and what a difference! Even though the cooktop is over 20 years old, it looks new again. Thanks to the knowledgeable support people at Part Select.Com we picked the right knobs the first time.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCarolyn from Fulshear TX
20 year old countertop - dials unreadable
Two dials available, chose the wrong one, PartSelect paid to have the wrong ones returned and issued credit, while helping to select the correct ones. Friendly, REAL people, who absolutely sealed the deal. I'll always check here first for parts, filters, anything. Thanks PartSelect
|