2200568-1-M-Whirlpool-Y313538-Heater-Element-240V.jpg
2200568-1-S-Whirlpool-Y313538-Heater-Element-240V.jpg 2200568-2-S-Whirlpool-Y313538-Heater-Element-240V.jpg 2200568-3-S-Whirlpool-Y313538-Heater-Element-240V.jpg

Heater Element - 240V

PartSelect Number PS2200568

This is a pre-stretched heating element coil and it carries 240 volts.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Compare At

    $48.29
  • You Save

    $8.05
  • Your Price

    $40.24
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 10 reviews What's this?
1-10 of 10
 

17 of 17 people found this instruction helpful

Parts Used

  • Heater Element - 240V

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerTom from Sitka AK

Our maytag dryer stopped producing hea

I am writing this story in the hope it will save time and trouble for others. I have used PartSelect with great success after our washing maching burned through a belt last year, so after our old Maytag dryer stopped heating, I looked on your website. I found it was probably the heater element so I ordered it and also printed off the blueprints and repair steps of my dryer since I no longer had the book. When the part finally arrived (5 days on a 2 day shipping charge-- I wasn't happy with the 5 days), it had different instructions on the heater element package than the PartSelect website offered. This is where things got difficult; what should have been a 20 minute job took 2 hours because I followed the directions on the package and took the dryer apart from the back instead of from the front panel side. By the time I figured it out, I decided to keep going anyway and ended up taking virtually everything apart (body shell, top, motors, wiring harnesses- anything I could disassemble) cleaned everything, and put it back together. So I believe that it all worked out for the best anyway since I will get many more years out the dryer for doing that. If you don't want to take the whole machine apart (and I am sure most people do not), just take off the front panel. There are two screws located near the bottom of the front panel; take these out and lift the front panel up halfway by tilting, then pull out. The heater element is right there on the lower right side. Make sure to follow the directions on the PartsSelect website and you will be fine. The most important tool for me was a 1/4" socket. Make sure you have this before you start. Having one that attached to a straight driver (like a screw driver) instead of a ratchet worked best. The dryer works like new now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

  • Heater Element - 240V

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerDonald from Woodlawn TN

Heating element burnt out!

Removed front of Dryer, using screw driver and putty knife to push in the top clips. Front drops down. Disconnected wires to heating element. Then removed whole heating element chamber. Removed old heating element from chamber. Then installed new heating element insude of old chamber. Reinstalled chamber in dryer. Hooked up all wiring. Note! Dryer "must be unpluged" before starting any work! Last step reinstall front of dryer. Repair complete!

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerNikiforos from Skillman NJ

No heat - otherwise worked fine

Although I ordered the heating element and thermal fuse in anticipation I really needed the Terminal Insulator kit for the heating element. The screw that the heating element is attached to on one side and the power supply on the other snapped (the weld joint came apart). First removed the front panel by unscrewing the two screws that hold it in place which are located about 4" from the floor. Next removed the front cover of the heater housing by undoing the two screws that hold it to the bottom plate and unscrewed the nuts that hold the heating element in place on the inside and the outside of the heater housing. Assembly was easy just follow the steps backwards.
! When the front is off it is a good time to use a vacuum cleaner to remove the lint that accumulates everywhere, especially in the air output !

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers

CustomerDavid from Erie CO

Dryer would not heat, noisy tumbler

First step was diagnosis. I unplugged the dryer and removed the front panel to access the heater. I disconnected the push on terminal at the heater over temp sensor and tested heater for continuity using a DVM. No continuity meant the heater element was bad. I visually inspected the tumber belt and found it to be split. I ordered the parts heater element and belt from PartSelect on a Thursday at 2:00 PM. I received notice that they shipped the same day! FedEx delivered the parts by Saturday. It took me about an hour to remove the heater and replace the element (its the 2nd replacement in 28 years) and about another hour to replace the belt and do a general cleaning of the dryer interior. All in all, it was a fairly easy repair (for a technically inclined guy).

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customerleroy from putnam CT

Heating element brunt out after 25 years!!

you must remove the element tube from from the dryer,{ mark all wires prior to },lay the unit on a bench,remove two screws-open the tube like a big book. then take a pencel and follow the element as it goes through the insulators. remove the two screws on both ends of the element & remove. to reinstall-reverse procedure-make sure to the element very snug-the instruction sheet is very good!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Heater Element - 240V

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set, Wrench set

CustomerJeff from Hooksett NH

Heater elemtn burnt out

1: Removed heater cowling by removing 3 screws holding it in place.
2: Opened two halfs of the cowling by removing 4 screws on the flange.
3: Removed 2 nuts holding element ends to the cowling.
4: Removed bad element making note of how the element was threaded through porcelin element bracket/holders.
5: Installed new element.
6: Reversed steps 1-3

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerDustin from Washington MO

Heater coil grounded out and push to start button was broke

I got a free Maytag washer and dryer set. All I had to do was put a new coil and start switch and it works. I did double check the wiring with the diagram behind the control panel. Everything went smooth...very easy repair. Thanks partselect for the quick shipping and parts. I can know save my money from the laundromat which is so expensive these days. Easy fix..just make sure the wiring is good before making these repairs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Heater Element - 240V

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJohn from College Place WA

The dryer no longer would heat to dry the clothes

I first unpluged the dryer, then I removed the front cover of the dryer. The Heating unit in located in the lower right side of the machine. I unscrewed the heating "tube" from the dryer and unpluged it from the dryer. ( good idea to mark the wires because they are same color.) I unscrewed the two halves of the heating unit and saw that indeed the heating coil was broken. I unscrewed the coil and fed it through the insulators. The coil was old and uncooperative, so I decided to cut it at each insulator with wire cutters. This sped up the process and protected the insulators. I carefully fed the new coils through the insulators and attached the ends to the terminals. Be careful not to over tighten or you may break the insulation on the terminals. I reinstalled the heating unit and attached the wires and tested the dryer. Job Done! Thanks Parts Select!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerRonald from Mankato MN

Heater element burned out in dryer.

Had replaced the heater element a few week earlier under the thought that it had failed just because the dryer was old. But shortly after replacing the element the dyrer started making a lot of noise when started. A few dryer loads later the hearte element had faild again.
The design of the Maytag Dryer makes most repairs easy. The machine is very well made.
Since I was investigate the noise that the dyrer was making, I did a complete teardown of the dryer to check things out. Fould that the drum drive belt was old and the blower fan had spun off the locking tab and also that the heater element was burned out. again. Did a complete check of all moving parts and orded the parts that needed to be replaced. Did a clean up of all old lint in the dryer vent system and fan unit. The fan and belt parts were easy to replace. The heater element does take time and care when working with the ceramic holders. But since I had done it before I did not find any surprised.
The dryer works like new now. Just hope none of the sensors or ideler wheels give out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Heater Element - 240V

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set

CustomerSoonja from Port Angelas WA

Dryer runs without heat.

How to repair a Maytag Dryer. (Call the nearest serviceman.)
Shut off the power and unplug the machine.
Open the 'box'. Two screws in the front near the floor and hinge open.
Make a diagram of ever screw and piece you remove.
Diagnose the problem.
Order the necessary parts from ....
Replace the part. (The element replace the second time in 30 years.)
Give the box a cleaning inside and out.
Put it back together.
Make sure all the parts you took out go back in.
Plug it in and turn on the power.
Test it.

Using a magnet to hold all the screws was helpful.
Having all the right tools is helpful. The requirements were pretty basic.
A good mechanical aptitude is essential or very helpful.
It is very important the exhaust port is patent. A leaf blower would be helpful in testing. I reversed the hose on our vacumn cleaner and packed foam around the tubbing to test it. (The local dealer warn me about using too much of the clothes softner.)
Karl Spees on behalf of my wife Soonja

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-10 of 10