2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt
2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-2-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-3-S-Whirlpool-Y312959-Tumbler and Motor Belt http://www.partselect.com/Schematics/Maytag/36762.gif

Tumbler and Motor Belt

PartSelect Number PS2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.
  • Takes too long to dry.
  • Will Not Start.
  • No heat or not enough heat.
  • Compare At

    $14.45
  • You Save

    $2.41
  • Your Price

    $12.04
Special Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drum Support Roller Kit

Part Number 1570070

This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and is recommended to change both at once.

$15.85
In Stock

Idler Pulley Wheel

Part Number 2347254

This part is used to help the belt to rotate the drum.

$7.91
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 178 reviews What's this?
 

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Ronald from Mankato, MN

Heater element burned out in dryer.

Had replaced the heater element a few week earlier under the thought that it had failed just because the dryer was old. But shortly after replacing the element the dyrer started making a lot of noise when started. A few dryer loads later the hearte element had faild again.
The design of the Maytag Dryer makes most repairs easy. The machine is very well made.
Since I was investigate the noise that the dyrer was making, I did a complete teardown of the dryer to check things out. Fould that the drum drive belt was old and the blower fan had spun off the locking tab and also that the heater element was burned out. again. Did a complete check of all moving parts and orded the parts that needed to be replaced. Did a clean up of all old lint in the dryer vent system and fan unit. The fan and belt parts were easy to replace. The heater element does take time and care when working with the ceramic holders. But since I had done it before I did not find any surprised.
The dryer works like new now. Just hope none of the sensors or ideler wheels give out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Socket set
Customer: Francis from Half Moon Bay, CA

Loud, rumbling noise

1. Removed two screws from front panel.
2. Removed panel.
3. Removed four bolts off tumbler face.
4. Removed face.
5. Removed drum and belt.
6. Vacuumed.
7. Replaced idler spring assembly.
8. Replaced drum.
9. Replaced belt.
10. Rotated drum to make sure belt was properly seated.
11. Replaced tumbler face.
12. Replaced front panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Wesley from Tulsa, OK

Trying to install the drum belt by reaching in from the front over the top of the blower & motor.

I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Benjamin from Baton Rouge, LA

Very noisy.

My first attemp was to replace the drum roller and idler roller, drive belt, and the felt seal for the back, since I had experience replacing these on an older machine many years ago. The dryer was very easy to work on....After installing the new parts, I reassembled and discovered it still made the same loud noise. I then, disassembled for the second time to discover the blower wheel was worn out; so i ordered another blower wheel and a drum support roller (i only ordered one the first time.). After reassembling it made an annoying high pitch sound. I attributed that to the new parts...probably the new belt and new felt seal. Gave it some time to run-in and it seems to have quieted down. Overall, i found the dryer very easy to work on. I actually found the felt seal the most onerous to install....needed to have about three hands to get the drum back in place! I just wish that the stamped metal dryer housing didn't have such sharp edges. I had to be very careful to avoid sharp burrs but still got nicked a couple of times.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Socket set, Wrench set
Customer: ROBERT from MORGAN CITY, LA

Black marks on whites and dark

The repair went better then I thought it would go.
the seals went on just fine

Help other customers find the most helpful instructions.

Were these instructions helpful?