2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt
2200550-1-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-2-S-Whirlpool-Y312959-Tumbler and Motor Belt 2200550-3-S-Whirlpool-Y312959-Tumbler and Motor Belt http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/36762.gif

Tumbler and Motor Belt

PartSelect Number PS2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.
  • Takes too long to dry.
  • Will Not Start.
  • No heat or not enough heat.
  • Compare At

    $14.48
  • You Save

    $2.41
  • Your Price

    $12.07
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drum Support Roller Kit

Part Number 1570070

This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and is recommended to change both at once.

$16.51
In Stock

Idler Pulley Wheel

Part Number 2347254

This part is used to help the belt to rotate the drum.

$7.71
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 178 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRonney from Glen Rose, TX

Blower wheel assembly worn causing a noise at startup and sometimes while running

I removed the screws to the front panel which allowed access to the inside. There were four screws that held the drum in place. I removed the drum to have more working room. Once inside, I removed the screws, clamp and clips that held the blower wheel assembly in place. After removal, I replaced the old blower with the new one and installed the new belt. I reassembled everything and the dryer runs like a new one. Very easy job that saved me lots of money. Also, the diagrams on your site were very helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMarlene from Cape Coral, FL

Dryer wouldn't tumble

removed the front panel, pulled out the drum, applied the new belt, reassembled, put in screws and voila.....the dryer worked.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerBrian from Jackson, WI

Broken drive belt

Remove the two screws under the door, lifted front panel outward and pulled it free at the top, removed the lint trap assembly ( 4 screws). I pulled the entire dryer drum out and cleaned out the inside o fhte dryer cabinet. Gettting the belt to track correctly took a little fiddling- I had to take the small panel off the back to access the motor pulley to feel the belt and get it set on the drum in the correct spot.

Overall, installing a new belt was fairly easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

CustomerJohn from Fremont, CA

Noisy when in use - cracken and broken belt

Well lots of other people here described the process and thats basically what I did.
Unscrewed the front of the dryer and behold the mountains of filth, lost toys, and spare change. Unplugged the dryer. Did some basic cleaning but wanted to get to the matter at hand.
Unscrewed the lint trap - realized I did not need to and put it back on. Unscrewed the 4 screws holding the drum and pulled the front off.
I just cut the old belt off. It was cracked and about to go. Put the new belt on and snaked it back into place. Opened up the back hatch and got it into place via the diagram. (It was spot on)
Put it all back together, plugged it in and started it up.
Hmmmm.. a odd rubbing noise.
Took the front off and looked around. Things looked fine. Checked the belt and started making sure it was working right.

NOTE!!!!!!! It is plugged in at this time you idiot.

Ok, so im trying to get the belt in the right spot and checking how the drum turns when i pull the belt. Well my arm touches the contacts for the dryer element and shocks me. Natural reaction is to yank my hand out as fast as I can. In doing so I punch a nice big gash into my palm. So laying on the floor, shocked, bleating, and its a flithy cut with lint in it.
Yeah me!!

After stopping the bleeding and cleaning it with peroxide I got back to it the next day.

I had the belt IN the grove of the drum. I messed around and moved it OUT of the grove. Worked perfect. While it was in the grove there was not enough tension. Moving it to the main drum tightened and had it go perfectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tumbler and Motor Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJohn T from Akron, OH

Snapped tumbler belt

Given the age of my dryer, the repair wasn't exactly as proposed on the belt's packaging, but it provided a great drawing of how the belt should contact the motor drive, pulley wheel and drum at the same time. First, I took off the front cover of the dryer with a nut driver. I discovered that I had to put the belt around the drum first and then use my arms to hold the drum up as my hands simultaneously pulled the motor pulley tight and threaded the belt around the motor drive and pulley wheel. After not quite slipping the belt on correctly the first time, I was able to very easily do it on a second try. Had I gotten the belt on correctly the first time, repair would have taken ten minutes. Runs great!!

Help other customers find the most helpful instructions.

Were these instructions helpful?