2200270-1-M-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg
2200270-1-S-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg 2200270-2-S-Whirlpool-Y303836-Blower-Wheel-with-Clip.jpg

Blower Wheel with Clip

PartSelect Number PS2200270

This comes with a metallic hub clip to hold it firmly in place.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not tumble.
  • Compare At

    $23.23
  • You Save

    $3.87
  • Your Price

    $19.36
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Blower Wheel Clamp

Part Number 600181

$2.70
In Stock

Tumbler and Motor Belt

Part Number 2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

$18.86
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 141 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Mentor OH

Dryer rattled in operation

Unplug the dryer. Remove two screws to remove the front drum housing. Remove 4 screws to remove the front drum housing. The front panel and front drum housing do not need to be unwired to work on the blower. Loosen wire harnesses and move panel and housing out of the way. Remove 2 spring clips holding the blower assembly to the motor shaft. Remove blower. Install new blower and re-assemble in the reverse order. The other stories written on the subject were spot on. This repair also made the clothes dry more quickly. I did not realize that long before the ryer made noise, there was a reduction in air flow. A simple vacuum switch to monitor air flow would tell you when there is a problem or that the filter/duct needs to be cleaned.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJames from Jenkins KY

Dryer making noise, blower mounting hole stripped out

I took two screws out to remove front panel, took out four screws to remove front drum panel,took out seven screws that hold cover to blower assembly , took off C clip and removed blower wheel. replaced in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerMichael from Carthage MO

Blower motor running and heating. Decrease in air circulation.

Using a blowup of the appliance, I removed the two screws that hold the front on and removed. Using the correct sized socket, I removed the housing that holds the front of the dryer drum in place and disconnected the wire to it. I then removed a shield near the blower unit and unbolted the front of the blower assembly. I could not get my power drill into position to take off the very bottom bolt but found that it would pivot forward enough to gain access to the blower fan. I then busted a knuckle trying to get the keeper washer off of the shaft (don't have a C ring tool). With some cussing and another scrapped knuckle, I took off the keeper ring and removed the fan, replaced with new fan and ring, broke the C ring trying to replace it so just left it off. I then went to cleanse wounds and apply dressings.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set, Wrench set

CustomerStephen from Gibraltar MI

Rumbling when dryer was running and also for about 5 seconds after dryer stopped

Removed the two lower screws holding front of dryer assembly in place and "unhinged" it and stood it up on floor. Then I unclipped the two wire leads on inside of dryer door assembly and moved assembly completely out of work area. Next I removed the four screws holding the tumbler frame in place and removed that frame from the work area. Now you can access the blower wheel "frame" and remove 5 or 6 hex screws to get that off and out of your way. You DO NOT have to remove the dryer drum and/or drum belt to complete this repair, so save yourself some work and leave it in place!! Once the blower wheel frame is off, use pliers and a flatheaded screwdriver to get the small outer retaining clip off, and then just pliers to get the wheel retaining ring off the wheel shaft. Put on the new blower wheel, use pliers to replace the aforementioned wheel retaining ring, and then the small outer retaining clip...VIOLA! You're finished! Dryer will run like new with a smooth purr instead of that dreaded rumbling sound.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerTima from Pomfret Center CT

Rumbly noise

I removed the front panel (two screws at bottom, then lifted bottom toward me until the top holders slid out). Then I unscrewed the front assembly that holds the dryer drum (four screws), first propping the drum from below so it would stay in place. I removed the blower housing (seven screws) and could see that the blower wheel was loose on the spindle. The 'D' shaped fitting had rounded out. A pair of snap ring pliers made removing the retaining ring and the wheel clamp a cinch and saved a good deal of teeth gnashing. I slid on the new blower wheel and then did everything in reverse. One caution: be sure the drum is pushed firmly up and back when reattaching the front assembly. (It can be done successfully with two hands). I had to re-do this part of the reassembly because the bottom of the drum was rubbing against the blower assembly. Once that was corrected, the dryer ran noiselessly. Thank goodness for PartSelect's diagrams. They're invaluable.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRonney from Glen Rose TX

Blower wheel assembly worn causing a noise at startup and sometimes while running

I removed the screws to the front panel which allowed access to the inside. There were four screws that held the drum in place. I removed the drum to have more working room. Once inside, I removed the screws, clamp and clips that held the blower wheel assembly in place. After removal, I replaced the old blower with the new one and installed the new belt. I reassembled everything and the dryer runs like a new one. Very easy job that saved me lots of money. Also, the diagrams on your site were very helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

Customerjohn from North Liberty IA

Blower wheel stripped

opened the front with 2 screws, removed 4 screws to access blower, removed spring clamp and split ring, pulled off old part and replaced with new and put back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerLaurence from Leesburg VA

Rattling noise and slow drying.

Turn off circuit breaker or unplug. Remove two screws 4 inches from bottom front panel of cabinet with stubby phillips head. Pull panel towards you about 30 degrees; then wiggle it down, to free two steel spring clips holding it to cabinet. Pull off red and yellow wire from door switch. Now set front panel aside. Blower assembly is facing you at lower left. Open the housing by removing six small screws from cover and one attached to dryer base. Remove spring clip from end of shaft. (A circlip pliers helps to prevent it from springing off somewhere.). Squeeze spring retainer surrounding blower wheel shaft with regular pliers, and wiggle the blower off. Replace in reverse order. Be sure insulation around blower wheel housing seats properly into front panel. This keeps the hot air flowing up past the lint trap.
Easy job, about half hour. Mine took longer, because I had removed the belt and drum, thinking the noise came from bad drum support rollers. It was just the plastic blower wheel shaft seat, which had worn itself round. Cost $20 (including shipping) and my 29-year old Maytag is as good as new--at least for now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerEdward from Collinsville IL

Ratling noise and clothes not getting dry

The blower had lost its key and was not attached to the motor. To do the repair: Remove the front cover, remove the lint screen assembly, remove the front of the blower housing. Use snap ring pliers to remove the blower wheel and install the new one. Reassemble and your done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerGeorge from Smithfield KY

Dryer rumbled and rattled

I removed the two screws holding the front cover and set the cover aside, then the two screws at the top of the dryer and unplugged and tagged wires going to the front panel and door assembly and set the front door and panel aside. Next I removed the 4 screws inside the tub attaching the lint filter and exhaust duct, and then the screws holding the blower cover. Then I removed the snap ring holding the blower to the motor shaft and pulled the blower off, slid the new blower on, and reinstalled the snap ring. While the unit was apart, since the lint filter felt gasket was out, I cleaned the gasket groove and cemented the gasket in place with Gorilla Glue. Finally, I reassembled all parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerWilliam from Thomaston GA

Loud thumping noise while dryer was on

Unplugged dryer. Removed two screws and removed front of dryer disconnecting the wires from the front. Removed 4 screws and blue wire allowing the me to take the shroud off. Removed blower fan cover by taking out the screws and pulling down. Used pliers to take off clamp on blower fan and then had to use snap ring pliers to remove snap ring. Pulled blower fan off, replaced with new and put back on snap ring and clamp. Reinstalled blower cover, Removed drum by cutting belt (noted the direction of the belt around the idler pulley). Replaced belt (decided since I was going to be in the dryer and it is 14 years old I would replace belt as well) and drum. Reinstalled shroud and front cover. Dryer is very very quiet now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

CustomerKevin from Rineyville KY

Living overseas and caring for a dinosaur dryer

My friend Saeed did the repair (which was really maintenance) for me. What I really want to communicate is how WONDERFUL it is to use PartSelect for folks like us living overseas and keeping alive an ancient gas dryer (not available in Morocco and infinitely cheaper than electric). We don't have a local Maytag parts dealer, so we feel lucky to have this option of using the diagrams to order exactly what we need to keep our economical and efficient gas dryer going.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerThomas from Venice CA

Dryer loud thumping noise.

Problem was the blower wheel, (Plastic deteriorated). Replaced the tumbler and motor belt as well as th idler pulley. While the blower wheel turned out to be the problem, the other parts were significantly deteriorated. Since I had the dryer disassembled it made sense to replace the other parts. The 24 year old dryer runs like new. The parts select instructional videos were extremely helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerRonald from Aliquippa PA

Noise coming from dryer and low air flow

Remove front panel, front drum support, remove belt, drum, blower cover, spring clip, blower cover, blower wheel assy.
Ordered new parts on line, came in two days, good service. Cleaned out all lint and installed new parts in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerCordell from Mount Pleasant MI

Took ~3hours to dry!

First removed the front of the dryer by removing two screws and tipping the front off. Took off the the front that holds the dryer drum by removing four bolts/screws. One screw to take of circuit protector plate, then about 8 little screws to remove the front of the blower house. Used a screwdriver and pliers to twist off the retaining ring and then swapped out the new blower fan for the old, broken one. Reverse to put it all back together. Trickiest was getting the retaining ring back on without the specialized tool they make for the job, but got it on with the pliers and screwdriver.
$25 bucks in parts and a half and hour sure beat $60 for them to tell me what is wrong (I already know) and then the mark up on parts and another $60 for the repair. Likely saved >$125.

Help other customers find the most helpful instructions.

Were these instructions helpful?