2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clip
2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clip 2200270-2-S-Whirlpool-Y303836-Blower Wheel with Clip

Blower Wheel with Clip

PartSelect Number PS2200270

Manufacturer Part Number Y303836
Manufactured by Whirlpool

This comes with a metallic hub clip to hold it firmly in place.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not tumble.
  • Compare At

    $20.02
  • You Save

    $3.34
  • Your Price

    $16.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Blower Wheel Clamp

Part Number 600181

$2.70
In Stock

Tumbler and Motor Belt

Part Number 2200550

At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.

$16.24
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 141 reviews What's this?
 

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customerleroy from putnam CT

Heating element brunt out after 25 years!!

you must remove the element tube from from the dryer,{ mark all wires prior to },lay the unit on a bench,remove two screws-open the tube like a big book. then take a pencel and follow the element as it goes through the insulators. remove the two screws on both ends of the element & remove. to reinstall-reverse procedure-make sure to the element very snug-the instruction sheet is very good!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerWesley from Tulsa OK

Trying to install the drum belt by reaching in from the front over the top of the blower & motor.

I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerRonald from Mankato MN

Heater element burned out in dryer.

Had replaced the heater element a few week earlier under the thought that it had failed just because the dryer was old. But shortly after replacing the element the dyrer started making a lot of noise when started. A few dryer loads later the hearte element had faild again.
The design of the Maytag Dryer makes most repairs easy. The machine is very well made.
Since I was investigate the noise that the dyrer was making, I did a complete teardown of the dryer to check things out. Fould that the drum drive belt was old and the blower fan had spun off the locking tab and also that the heater element was burned out. again. Did a complete check of all moving parts and orded the parts that needed to be replaced. Did a clean up of all old lint in the dryer vent system and fan unit. The fan and belt parts were easy to replace. The heater element does take time and care when working with the ceramic holders. But since I had done it before I did not find any surprised.
The dryer works like new now. Just hope none of the sensors or ideler wheels give out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerThomas from Venice CA

Dryer loud thumping noise.

Problem was the blower wheel, (Plastic deteriorated). Replaced the tumbler and motor belt as well as th idler pulley. While the blower wheel turned out to be the problem, the other parts were significantly deteriorated. Since I had the dryer disassembled it made sense to replace the other parts. The 24 year old dryer runs like new. The parts select instructional videos were extremely helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerStephen from Crawfordsville IN

Broken belt

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRoger from Owatonna MN

Blower fan was broken and spinning on the motor shaft

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerCody from Nebraska City NE

Clunking noise when first turned on

I took the access panel off the back, realized that belt was in very bad shape. Ordered a belt when I got that changed I put it back together and it still had a clunking noise. Found out that the blower wheel was rounded off where it goes over the shaft. So to change that I took the two front screws off, then the four hex screws off of the tumbler guide. There were eight or so screws over the blower wheel, took those out and the clamp on the blower wheel then used the snap ring pliers for the snap ring, then changed the wheel. Problem solved. This website is very helpful I would not have attempted to fix my dryer without this website.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerRICHARD from ROBINSON IL

Blower wheel hub worn out

First remove 2 screws on bottom of front panel,pull panel out from bottom to remove. Then remove 4 screws,2 on each side to remove tub support. Then remove approx.6 screws on fan access cover to expose fan. Then remove snap ring and clamp on fan hub. Pull fan off and push new fan on and reverse procedure.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench set

CustomerCARRIE from NEW BAVARIA OH

Loud knocking in the dryer

My husband took off the front panel and noticed that the center of the wheel was melted. We went on to this website and confirmed the noise with other customers. We ordered the part - received it in 1 day and the dryer was repaired and back together within a 1/2 hr. Part was as is - istructions excellent.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHenry from Newark Valley NY

Fan was noisy, indicateing that the fan hub was worn, letting it wobble.

I removed the two screws and removed the front panel, next I removed the fan cover that also directs the air movement into the drying tub. I then removed the external snap ring that held the fan in place on the shaft. The fan very easily slid right off of the shaft. It was reassembled in the opposite order. A very easy procedure. The entire procedure was not more than one hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRonald from Cadet MO

Making loud noise

Removed (2) screws at bottom of dryer. Removed about 5 screws on blower housing. Used pliers to remove clamp and replaced the blower. Installed everything in reverse. I looked at what others did before me and it made it easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerAnthony from Citrus Heights CA

Horrible rattle - sounds like drying a load of cleats

I followed the instructions given by other DIYs. The rubber band for the belt was a great suggestion, however having no rubber band nearby, I used a zip-tie that worked out perfectly.

The only tool that I wished I had is a pair of split ring pliers. Not having a pair, used a pair of needle nose and a very small screw driver to provide the leverage to remove the washer.

After following the instructions that came with the belt on how to properly align it to the motor wheel and tension wheel, I plugged everything back in and started it up. Sounded like it was brand new.

I decided not to replace the rollers or drum guides as they looked to be in good shape.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench set

Customerjohn from paw paw MI

Bad rumbling noise

Found the answer online, ordered the blower from here. I used a pair of scissors in place of a snap ring pliers. Otherwise went smoothly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set, Wrench set

CustomerJames from Hicksville OH

Dryer noisey

took off front of dryer then front of drum supports then took the blower fan off and replaced it. pulled the drum out replaced the shafts and rollers put it back together was not a very hard job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Blower Wheel with Clip

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerJoseph from Ontario NY

Initially the dryer made a loud rumble during startup, it progressed until the noise was continuous during operation.

Because of the nature of the noise, and knowing nothing of appliance repair, I assumed that there was a loose belt. I figured that the belt would be accessible from the rear of the machine. After much disassembly, I discovered that the belt was in fine shape and not the problem. But every time I spun the drum, I could still hear the rumbling sound. Eventually, I discovered that the from paned of the dryer is the easiest to remove. Once I removed that, I discovered the blower fan housing. A few screws later and I could see that the plastic fan center was worn out. I had a part number so I simply did a quick internet search and found several sites that stocked it. PartSelect had the best price and the best shipping prices as well. I placed the order on Saturday afternoon. I got the confirmation immediately, and the shipping information on Monday. On Wednesday the part was waiting at my door! It took about 15 minutes to re-assemble the dryer and now, about 18 loads later, it's perfect!
Thank you PartSelect!!!!
Joe G

Help other customers find the most helpful instructions.

Were these instructions helpful?