Quick Question!

Have you ever purchased from PartSelect.com before?

2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clamp
2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clamp 2200270-2-S-Whirlpool-Y303836-Blower Wheel with Clamp http://www.partselect.com/Schematics/Maytag/36762.gif

Blower Wheel with Clamp

PartSelect Number PS2200270

This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses air through the drum and out of the exhaust vent. This part might need to be replaced if you notice your dryer is taking too long to dry clothing, it is not tumbling, or is making any unusually loud noises. The blower wheel measures about 7.5 inches in diameter by 3-3/8 wide. The blower wheel can be accessed by removing the front panel of your appliance.

This part works with the following brands: Maytag, Jenn-Air, International.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Noisy.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not tumble.
  • Too hot.

Compare At

$18.06

You Save

$3.01

Your Price

$15.05
Order within the next 4 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Blower Wheel Clamp

Part Number 11740752

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

Order within the next 4 hrs and your part ships today!
$5.81
In Stock

Tumbler and Motor Belt

Part Number 11757542

The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair.

Order within the next 4 hrs and your part ships today!
$13.81
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 146 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Oscar L from Buena Park, CA

Replaced blower..

Removed the 2 bottom screws under the front cover. Lift up and you could set it aside. Remove all the blower screws using a nut driver. Here you, you will see the blower and remove the lock ring using a ring pliers and the clip using a needle nose pliers. Remove the old blower and install the new one, make sure the flat side of the shaft matches with the blower. Put back in reverse order all you remove..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Dale from Mentor, OH

Very noisy

I just followed the video to the letter or recording

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: George from Key West, FL

My wife, the dear little thing, heard a clunking noise when she turned on the dryer.

I am a builder and a fixer, but have never fooled around with washers and dryers. They just seemed too big and complicated and specialized. But for some reason this time I went to a Maytag parts site, ended up with Parts Select, and happened across the question of what was my problem. The loud noise answer showed most likely causes of noise, so I ordered the two parts with the the best chance to be the culprit. Then I found the video with the nice guy doing the job slowly and clearly, and it looked like a snap. It was sort of like the old Volkswagon Bug "Repairs for Idiots Book" or whatever it was called: "First, open the hood. Second, prop up the hood with a stick so it won't fall down on you. Third . . . ." Received the parts in the mail, pretty reasonable, looked at the video a second time, and opened 'er up. I was amazed at all the space in there, and how simple everything was. Wiggled and spun the rollers, then spun the fan and there it was - the grinding noise. So I replaced the fan, put it back together and the problem was solved. Later I had to put in a new belt too, so I recommend doing that any time you take out a major part in an old dryer. My old belt was sorta cracked and I should have replaced it along with the fan but I thought it would keep on working. Stupid me. But the whole program was just right for someone with an hour or two who wants to save that $150 repair bill from an appliance repair guy who comes to your home and does the exact same thing you can do yourself. Just LOVE the probability percentage list of which part is bad, and the videos on how to do the work. I'll use this system again, if needed. George

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: Craig from Falcon Heights, MN

The dryer was really loud when in use.

I replaced the drum rollers and guide pads, and the blower. Now everything works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Austin from Cupertino, CA

Rumbling / groaning noise when dryer starts

I thought the noise was coming from the rear belt / pulley system, but found it was from the front blower wheel.

First phase: disassemble to figure out problem -- found the front glides were worn and tumbler belt was old & cracked and noise was from blower wheel. Vacuumed out tons of lint. Ordered parts. Had to order rivet tool & ring pliers (tools cost $25 including shipping). One hour.

Final phase: Disassemble & drill out glide rivets -- attach with new rivets (easy). Replaced blower wheel & belt (easy). One hour.

Runs great -- no noise. Cleaning helped drying ability. Videos were key. ALWAYS REMEMBER TO UNPLUG! I didn't & nearly welded my fingers to the chassis.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: john from fairbanks, AK

Noise when drum turned

Parts replacement was easy after I watched your video on how to do repairs. The biggest issue no covered on the video was that a ring expander is required, (which I had to purchase), if removing any of the rollers or idlers.. Also the retaining rings need to be replaced if the machine is older because they bend easily.. Another issue to mention is that lot of lint, and other junk should be vacuumed inside the drier and vents.. Total repair cost was less than $100 so should be good for many years. Saved over half buying parts from you vs buying parts locally over the counter…

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: Paulette from Tewksbury, MA

Blower fan, no heat, much noise

repair went well, very fast delivery service, ordered Thursday, received Sat. morning.
took about 2 hours to do job, up and running by noon on sat.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Charles from East Haddam, CT

Rebuilding dryer

Put it back the same way you toke it a part

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers
Customer: Forrest from Chatsworth, CA

Loud banging noise

tell everyone to check the blower wheel, it starts out as mid tapping but increases overtime, anything that bangs real loud, its the blower wheel

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Dirk from Wayne, PA

Fan was broken

Removed front panel of the dryer. Removed front cover for the fan assembly. Remove snap ring, clamp holding fan assembly to drive shaft. Re-installed new fan, snap ring and clamp. Cleaned lint from fan area and re-assemblied. Also, replaced drum belt while apart. Very easy job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: ROSE from ROSCOE, IL

The dryer was making a terrible banging sound.

I removed the old blower, cleaned all the built up dirt etc and replaced the new blower wheel. Much to my amazement the dryer works like new and no more banging. I appreciate that you had the part we needed and it arrived so quickly. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: JAMES from WYNANTSKILL, NY

Need new blower wheel so I changed belt also

The service from PartsSlect was outstanding.
Parts arrived next day and where OEM. I had the
dryer cleaned and operational in 1.5 Hr's
Keep up the great service.



Thank You

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Rick from Zeeland, MI

Loud clanking noise at startup and noisy while running

Watched the video on PartSelect website linked to replacing the part. followed the steps shown in the video. The only problem that I had was removing the spring retainer clip. Once I used the correctly sized pliers it came off the first time. Now the clanking noise is gone.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: ARVID from SPRING, TX

Damaged keyway on dryer blower wheel

After struggling with increasing excessive noise emanating from the clothes dryer, the source of the problem was traced to the area near the electric motor. After some trial and error, access to the blower wheel area was possible. The blower wheel was found to “free-wheel” on the motor shaft which is obviously incorrect. The keyed area on the blower wheel was completely destroyed allowing
the motor shaft to spin freely in the keyway.

Removal of the blower wheel was straight forward although “E-ring” plier tool is necessary to remove the retaining ring. Finding the correct Manufacturers part number from on-line appliance sellers was somewhat a task as many types exist which look very similar. Note, look on the inside of the blower wheel and the number can be found stamped on the part.

Replacement of the blower wheel was not difficult however keeping the drum in position took some effort. I used spring clamps to keep the drum from slipping out of place.

End result is that I do not need to buy a new $$$ dryer much to the dismay of my wife. The unit sounds just like it did when it was first purchased.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Todd from Irvine, CA

Blower wheel was broken

I went online to your store and found it easy to identify the correct part and ordered the part which came right away. Thanks to your thorough online tutorial, I was able to easily replace the blower wheel within 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?