BBB A-Plus

Handle and Latch Assembly with Switches

PartSelect Number PS2180050

This part includes the black handle, the latch and the door switches as a complete assembly.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door latch failed
In Stock

  • Compare At

    $34.48

  • You Save

    $5.75

  • Your Price

    $28.73
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 3 4 NEXT > 16-30 of 57

 

1 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJason from Lima OH

Internal insert knobs broken from wear and tear

First of all, Partselect is definately has the cheapest price and quickest processing and shipping that I found. No im not getting paid for this. Anyway, Be sure to kill all power. Pulled the inside cover off, carefully not pulling wires apart. The handle assembly fell to pieces. There are two wire harnesses (minor current)that you need to disconnect and reconnect to new switches. Align mounting holes and insert screws. Replace inside panel and screw tightly and fix is complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerBryce from Lago Vista TX

Door would not open

The exterior lift handle had broken on both sides where it rotates and presses against the internal release mechanism. Eleven screws held the door panel together and also the lift handle/latch assembly. The new assembly dropped right into place. But it had microswitches already installed and I wanted to use the old ones since it was very difficult to pull off the wires. To install the old microswitches requires that you hold down each switch button so that the switch will fully clip into place. Next I put all the screws (torx type) back in

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerAARON from OCALA FL

The door would not latch

First I turned the power off at the elecrical panel. (there are live exposed parts on the inside of the door if you don't turn the power off and they conecet to the handel ) Then I removed the 9 or 10 tork screws that holds the inner part of the door to the outer part of the door. (Screws are on the inside of the door.) When you remove the screws this also losenes the bracet that hold the handle assmbley disconect the wires then put in the new one. the wires are a little hard to disconect. but that is about the worst of it . This part comes with every thing and and is cheper then buying it seperat. Sorry about the spelling. hope this helps

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEarl from South St. Paul MN

Unable to open dishwasher broken latch

Went to the hardware store and bought a T-20 torx tip and then unscrewed the plastic on the inside of the door, unplugged the dishwasher and replaced the latch assembly. This is an electrical part and it is essential to disconnect the power. I would never buy this dishwasher again. The latch is not something that should break.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customerjason from moundsville WV

Lattch to open door on dishwasher broke

Removed all screws on inside of dishwasher door. then removed latch assembly. unpluged to two connectors and put them on new. reinstalled all srews on inside of door and project complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerOtis from Canton NY

Door wouldn't latch

I turned offf the power to the dishwasher, then removed about 10 screws to separate the inner door panel from the outer panel. I disconnected wires from 4 terminals, attached them to the new latch assembly and reinstalled the inner panel. The web site was easy to use, but I had reason to call your service people.The lady I talked with was especially helpful. I have bookmarked your web site and would order again, when necessary.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Lancaster NY

Door handle was jammed up and closed very rough.

The part was great! It was like a cartridge that plugs into the appropriate slots and done! So glad I didn't call a repair man to do this. Anyone that is considering fixing their dishwasher should check out doing it themselves. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerThomas from Winnetka CA

The latch to the door was broken. Needed replaced.

Layed door flat. Unscrewed 11 screws on the inside of door. Lifted inside cover and pulled power cables from both sides of handle assembly.

Pulled old handle out and set new one in. Hooked up both power cables and reset inside cover.

Lined up screw holes and tightened.

Works perfectly. Very very easy. 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDavid from Two Harbors MN

Broken handle on dishwasher

Removed all the screws around the outer portion of dishwasher door. This would be the part of the door facing the dishwasher when the door is closed. When you remove the screws, this will loosen the handle, enabling the handle to be removed and easily replaced.

Easy as pie!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Austin TX

Door latch broken

Turned power off to device. Removed all of the torx srews on inside of door. Latch assembly rest between inside and outside door and comes loose once door is unscrewed. Initially tried to repair broken latch, but was unsuccessful. So I ordered latch assembly. Unplugged wire connectors...make sure you match the sides of the wire connectors when installing new assembly. Replace door and restore power.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerYee Pang from Philadelphia PA

Broken door latch

I was planning to have an appliance repair guy do it. But he didn't show up. So I went down to Home Depot to pick up a Hex screw driver bit. Came back, switch off power at the circuit breaker for the dishwasher, opened up the dishwasher, unscrewed the bolts on the door, removed the connectors from the latch assembly, connected the new one to it, put it in place and bolted down the door cover. The most difficult part was disengaging the connectors. The whole thing including the trip down to Home Depot was less than an hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMichael from Sweeny TX

Dishwasher door latch broke and would not open

MAKE SURE ELECTRICITY TO DISHWASHER IS OFF!!! If dishwasher is installed directly wired, TURN OFF THE BREAKER!!! Undo the inside plastic door molding....remove the old latch and install the new one! Easy to install! Wife is very happy!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerJeffrey from Rome GA

Handle broken

Remove the cover from inside the door, 11 torx screws. Take off the old latch assembly and handle, replace with the new handle and latch assembly made together now. Replace the 11 torx screws and you're done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSandra from Mill Valley CA

Dishwasher wouldn't open. The latch was broken.

I called the 800 number instead of ordering online.
The young woman I spoke with was very helpful.
Like others, I was confused about which part to
order. I live in Mexico. There's a factory trained technician in town, but no parts. So I ordered the
part, had it shipped to my daughter in CA, and
when I visited I picked up the part and brought it
back. The technician charged 150 pesos. (That's
about $11 usd.) I watched him and realized I could have done it myself. But why bother?

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

    • Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichael from Goshen NY

Broken latch

Before starting job found step by step video of repair on You Tube, part was slightly different, but steps were all the same. Removing and replacing all the screws on the door panel took more time then the part it self.

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 3 4 NEXT > 16-30 of 57