2180047-1-S-Whirlpool-W10130695-Door Handle and Latch Assembly with Switches
2180047-1-S-Whirlpool-W10130695-Door Handle and Latch Assembly with Switches 2180047-2-S-Whirlpool-W10130695-Door Handle and Latch Assembly with Switches 2180047-3-S-Whirlpool-W10130695-Door Handle and Latch Assembly with Switches http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/56225.gif

Door Handle and Latch Assembly with Switches

PartSelect Number PS2180047

This part includes the black handle, latch and 2 switches. This part is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door latch failure.
  • Will Not Start.
  • Door won’t close.
  • Leaking.
  • Compare At

    $34.61
  • You Save

    $5.77
  • Your Price

    $28.84
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Handle and Latch Assembly with Switches

Part Number 2180046

This part includes the white handle, door latch and 2 switches. This part is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open.

Order within the next 4 hrs and your part ships today!
$28.63
In Stock

Door Handle and Latch Assembly with Switches

Part Number 2180048

This bisque door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. Please NOTE: The bisque handle is no longer available separately. Only available with this assembly.

Order within the next 4 hrs and your part ships today!
$29.29
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 330 reviews What's this?
 

13 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWayne from Waterford, WI

Upgraded kitchen to stainless steel appliances

Shut off the power. Opened dishwasher door fully and removed 10 screws around outside edge. Lifted the inside panel up carefully and set to side with wires attached to soap dispenser. Removed two screws that held handle in place and removed wires. On the bottom o fthe door there are 4 screws 2 on each side that have to be removed from the hinges. You can now remove front panel. Take four screws out of control pad that hold the pad to the front panel. Simply reverse steps to reassemble. Takes about 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 11 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerStephen from Fenton, MI

Door latch was broken and also plastic in center of control panel

Removed all screws from the perimeter of the inner door panel

Removed (2) connectors from inner door panel and set it aside. Note this was difficult, but was finally accomplished by using a pliers and pulling on the connector body.
Instructions should be included on how to remove these to prevent damage.

Removed circuit board plastic cover.
Unplugged Flex circuit conductor strip from circuit board.
Removed control panel and door latch asm from outer door panel.
Replaced parts in reverse order.

Problem: The flexible conductor strip attached to the control panel had a sticky red adhesive at the tip extending about 3 inches and was stuck onto the panel. Was this for shipping reasons?
Anyway, the sticky goo would not let the strip plug into the circuit board or make a reliable connection.

The Dishwasher worked for one day then would not operate the next day.
I had to disassemble the panels again and clean the glue off with Goo Gone. I was taking a chance because I didn't know if the Goo Gone would affect the carbon conductors on the strip.
Anyway, it now is working again.

Suggestion: You need to include instructions about attaching the flat conductor strip to the circuit board.
Also, It does not seem proper to put the glue over the connector end of the strip. Even though the glue was on the side of the strip opposite the actual carbon conductors it got all over everything just due to handling and had to be cleaned off.
I would suggest tape or something more easily removed or apply the glue away from the tip a couple of inches or more.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Door Handle and Latch Assembly with Switches

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerROBERT from ALLEN, TX

Door latch failed

Turn-off the dishwasher power at the circuit breaker. Open the dishwasher door flat. Remove the 11 screws around the perimeter of the door using a t-20 torx bit (available at any hardware store). The latch assembly is held on by the top middle two door screws. Pull latch assembly out from top of door. Remove the black and white cable assembly connectors from the latch assembly making sure to note which side each color is on. If you have trouble sliding the connector off, use a flat screwdriver carefully to pry it, but do not pull on the wires. Install cable connectors onto new latch assembly making making sure the black and white cables are on the correct sides. Position the door at a 45 degree angle and place the latch assembly into position while putting the white inner door over it. Reinstall the 11 torx screws around the side of the door being sure the screws are snug, but not overtightened. Test the operation of your dishwasher. The new latch assembly seems to be built better than the factory original.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Door Handle and Latch Assembly with Switches

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerEdward from Charlotte, NC

Broken latch

Used torx bit to remove screws on door and removed the back of door. Removed wiring from switches (2) on broken latch and removed latch. Plugged in switches on new latch and placed latch in position. Screwed back of door into place and that was it! Very simple task and new latch looks and feels much more sturdy than old one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerEric from Ellensburg, WA

Door latch and seal not working correctly and broken

Removed the screws holding the door liner in place removed latch. Waited for half of the parts to get here, about 2 weeks. Parts got here except for Door latch and seal they were back ordered. One month after I ordered all parts finally arrive. Replace door latch assembly and replace door seal reinstall retaining screws....Done works good again. Parts were all the correct ones just took a long time to get here.

Help other customers find the most helpful instructions.

Were these instructions helpful?