Brake Pad Kit

PartSelect Number PS2174598

Included in this kit are three long shoulder bolts, three short boulder bolts, three brake pads, three short rubber grommets, & three long rubber grommets..

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $24.12
  • You Save

    $4.02
  • Your Price

    $20.10
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 3 reviews What's this?
1-3 of 3
 

8 of 9 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set

CustomerStephen from Kittanning PA

Brake pads were worn out

Unplug the washer
Took off the front with nut driver to two fasteners at the bottom.
Took off two tub springs using channel lock pliers.
Tipped the tub back for more hand room.
Took brake bolts off with box end wrench.
Put Screw driver above brake clamps and pried down to make the old brake pads drop down below the seats and then take brakes off. You might have to use a screw driver to expand the brake clamps so they will release the brake. (brake clamps look like a pulley but the edges will spread some bit.)
Twisted large screw driver between the brake clamps and pushed new brake in as far as would go while beside (to the left or right of) the brake seat.
Pried brake clamps down and rotated brake around until it is lined up with the brake seat. Then pried pads up into the seat.
Re-twisted large screw driver between the brake clamps to separate them and pulled the brake pad back to within 1/8th to 1/16th inch of the back. This lined up the bolt hole.
Inserted the bolt with rubber grommett into the brake pad hole and twisted it counter clockwise and tightened with wrench. (If the bolt would not thread, then you have to adjust the brake pad forward or backward until the holes line up.) Tighten the bolt until it is firmly tight.

There are three brakes. Each is installed the same way. The one in back required a little cross legged contortion for me to reach around both sides of the motor and two front brake pad mounts. The key is lining up the bolt hole in the brake pad with the mount. I pretty well had it figured out after the second pad install. Time for me.. 4 hours. Cost, leg cramps, sore muscles from awkward positions, and the joy of not having to buy a new washer.

Return the springs to the tub on the front. Close front panel and return the two fasteners with the nut drivers.

How did I know I needed the brakes? When in agitation mode the tub spun the opposite direction of the spin cycle. When the agitator turned the opposite direction, the water inside went into a very strong vortex and sometimes sloshed out the top or around the top edges When there were a lot of clothes and a high fill level in the tub. We also had trouble with straps winding around the agitator. The tub spun so quickly that the water without agitation was driven to the top outer edges of the tub by centrifugal force.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsWrench set

CustomerMartin from Grayslake IL

Water leaking when water level is set above medium. Wash tub spinning when during agitation cycle.

Three brake pads are located just above the drive pulley and space symmetrically around the brake wheel. Remove the one screw per brake, slide brake out of brake wheel and replace with new brake. Apply silicone grease to new brakes before installing. Tools: 5/16 boxed end wrench.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Brake Pad Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Anchorage AK

Agitator not working. Found worn brake pads which allowed tub to turn without agitating

After removing the front panel I was able to reach the bolts holding the brake pads in place. Without the above mentioned ratcheting end wrench it would have been very difficult to start the bolts while replacing them. I would probably consider removing the motor if I had to do this again. It would give a lot better access. no real difficulty other than hard to reach.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3