| |
10 of 10 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver
Customervalerie from gainesville TX
Dryer would not heat
i removed the front panel of the dryer, two screws on the bottom. then removed the 2 screws on the heating element that was located in the back of the dryer. pulled out the heating element and tested the parts with my husband's electrical equipment. the fuse and thermostat were bad. replaced those two parts on the heating element, connected all the wires back and screwed it back in the dryer. it works like a brand new dryer.
|
4 of 6 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)
CustomerRichard from Grayslake IL
No heat
I purchased the "M" series Ignition coil kit per" Ask How repair man". Installation was straight forward.
Simple repair when correct parts are used.
|
4 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers, Wrench(Adjustable)
CustomerDarrell from Edwardsville IL
Dryer runs but doesn't heat
No heat usually means a bad heating coil. Removed the heating coil and found a burnt element. Searched the internet looking for best price and fastest delivery. Ordered heating element and fuse kit from PartSelect on Tuesday, received parts on Thursday. Installation was quick and easy. Saved at least $100 using PartSelect!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerJOANN from PLEASANT VALLEY NY
The dryer wouldn't get hot
removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.
p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days
Thanks
JoAnn
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerBerkeley from Staunton VA
Dryer wouldn't heat
I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Wrench set
Customererica from Clemson SC
Dryer wouldn't heat
I should have know it was the fuse from the beginning but I figured this out after replacing the the heating coil. (I didn't have the tools to test the wiring, and everyone kept telling me it was the heating coil.)
Anywho, I replaced the thermostat first then the fuse. They were located on the outside cabinet of the heating coil. I plugged it up and then there was heat. They did look a little different from the original ones but you could tell which was which. The fuse is at the top and the thermostat at the bottom. I didint have to use the new wiring to the fuse because they looked fine. I did however had to use the wiring that came with the kit for the thermostat because the old one was fried and a little different from the original.
Well that's my story. Sorry if there's any lackness in the details.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:More than 2 hours
ToolsNutdriver, Pliers, Screw drivers, Socket set
Customerjane from ashland NE
Dryer plug was burnt, wouldnt run
replaced plug, still dead,read fixit book, mislead me , found online info, tested motor, thermal fuses,found bad one , partselect suggested a bad high limit also, bought kit, here in two days, works fine ,thanks
|