Fuse Kit

PartSelect Number PS2174577

This fuse kit comes with a thermal fuse, a high limit thermostat, two lead wires, & four mounting screws.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.
  • Compare At

    $49.27
  • You Save

    $8.21
  • Your Price

    $41.06
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 7 reviews What's this?
1-5 of 7
 

16 of 17 people found this instruction helpful

Parts Used

  • Fuse Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customervalerie from gainesville, TX

Dryer would not heat

i removed the front panel of the dryer, two screws on the bottom. then removed the 2 screws on the heating element that was located in the back of the dryer. pulled out the heating element and tested the parts with my husband's electrical equipment. the fuse and thermostat were bad. replaced those two parts on the heating element, connected all the wires back and screwed it back in the dryer. it works like a brand new dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench (Adjustable)

CustomerRichard from Grayslake, IL

No heat

I purchased the "m" series ignition coil kit per" ask how repair man". Installation was straight forward. Simple repair when correct parts are used.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

  • Fuse Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Wrench (Adjustable)

CustomerDarrell from Edwardsville, IL

Dryer runs but doesn't heat

No heat usually means a bad heating coil. Removed the heating coil and found a burnt element. Searched the internet looking for best price and fastest delivery. Ordered heating element and fuse kit from PartSelect on Tuesday, received parts on Thursday. Installation was quick and easy. Saved at least $100 using PartSelect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Fuse Kit

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerBerkeley from Staunton, VA

Dryer wouldn't heat

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Fuse Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJOANN from PLEASANT VALLEY, NY

The dryer wouldn't get hot

removed a couple of screws and replaced the new fuse . the dryer is heating up ok now.

p.s thank you for the quick deliever on the part, . as i was only with out the dryer for two days

Thanks
JoAnn

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 7