Water Inlet Valve Kit

PartSelect Number PS2167007

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No hot or cold water.
  • Will not stop filling with water.
  • Will not fill with water.
  • Compare At

    $68.59
  • You Save

    $11.43
  • Your Price

    $57.16
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 11 reviews What's this?
1-11 of 11
 

14 of 14 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerCharles from Vista CA

Washer wouldn't fill on hot selection, ok on cold

Remove the electrical power plug and disconnect the water hoses at the back. Remove the lower front panel by taking out the two screws at the bottom edge. Then lift out the upper front panel which exposes the two sheet metal screws holding down the top panel. Lift open the top panel and secure it up about 90 degrees so it doesn't flop over backwards. Twine tied to something overhead works fine. Replacement procedure for the valve is obvious, once exposed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerBill from Lafayette Hill PA

Washer filling very slowly

Unplug washer, turn off water supply, disconnect hoses from washer valve(have bucket ready for water remaining in hoses), Remove bottom front panel by unscrewing two hex head screws near floor then pulling panel toward you and down, remove top front panel same as bottom to expose screws securing washer top, lift washer top and prop open or tilt back onto counter(hold washer lid when tilting back). The inlet valve is on the back right. Label and unplug wires, unscrew hose clamp and remove hose, go to back of washer and unscrew plate holding valve and remove. Mount new valve to plate and fasten from back of washer, reconnect hose and wiring, close cover and fasten screws, replace front covers and secure, reconnect water supply hoses(do not over tighten), turn on water and plug in washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customersteve from ramsey MN

Low flow when cold water was used

it was really easy to gain access to the valve, but the part was just a little different then the original. I had to lengthen one wire to make the new valve work. This did take care of the problem when completed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerSteve from Churubusco IN

Mixing valve quit working - hot side

Needed part. Ordered Part from PartSelect Friday afternoon and figured I'd get it the following week. No big deal. Part arrived at my doorstep next morning before noon. UNBELIEVABLE SERVICE. Not requested, but it was there. So I fixed the machine as soon as I got it. I wish every company had this kind of service. I've already told my friends. It just can't get any easier than this.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerWalter from Hampton NJ

Water would not shut off

Sunday night - removed old valve and hose 15 min went online, found & ordered part - 15 min - part showed up Tuesday afternoon, replaced defective valve 15 min - did laundry! Couldn't have been easier or less expensive!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerLawrence from Saranac Lake NY

Water inlet valve was clog. Water was very slow to fill the machine.

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerLinda from Carlos MN

No cold or cool water only hot

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerDAVID from ORLAND PARK IL

Water inlet valve wouldn't work for cold water

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerMichael from Nampa ID

Pump leaked, water valve didn't have cold water

disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

CustomerRichard from Virginia Beach VA

Could not get adequate amount of cold water

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve Kit

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerSteven from Pembroke Pines FL

Hotwater was coming out slow to fill the was tub of machine

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11