BBB A-Plus
2163369-1-M-Whirlpool-M0805101-Ceramic-Fuse-20-Amp.jpg
2163369-1-S-Whirlpool-M0805101-Ceramic-Fuse-20-Amp.jpg

Ceramic Fuse - 20 Amp

PartSelect Number PS2163369

This ceramic microwave fuse is white in the center, while each end is made of metal. This is a twenty amp fuse.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Won’t turn on
In Stock

  • Compare At

    $4.21

  • You Save

    $.70

  • Your Price

    $3.51
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 NEXT > 1-4 of 4

 

20 of 21 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerJay from Edwardsville IL

Blows main fuse when the microwave generator start, (cooking function).

Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter.
Tried fuse, it does not blow untill cooking starts.
Check capacitor with ohm meter, after properly performing capacitor dischagre procedure.
Order new capacitor, simple installation. another new fuse and all is good and cooking again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 16 people found this instruction helpful

Parts Used

    • Ceramic Fuse - 20 Amp

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

Customertad from tamarack MN

Microwave oven blew fuse

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 11 people found this instruction helpful

Parts Used

    • Ceramic Fuse - 20 Amp

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customerconnie from madison NC

Died while heating lasagna

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 8 people found this instruction helpful

Parts Used

    • Ceramic Fuse - 20 Amp

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerDenice from Montgomery AL

Microve stopped working

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 NEXT > 1-4 of 4