Rear Drum Support Roller Kit

PartSelect Number PS2162268

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer this kit has been updated now to have one spacer that is the thickness of 2 spacers. To get these parts separately, please search by model#.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Compare At

    $45.49
  • You Save

    $7.58
  • Your Price

    $37.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 19 reviews What's this?
16-19 of 19
 

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRandall from Hoffman Estates IL

Load banging noise when drun turns

removed front cover 2 lower screws. once front cover was off, the front drum support bracket was visable. removed 4 screws that hold that in. the drum is now loose and not supported in the front. pulled drive belt tensioner back to release belt. removed 2 top cover screws to get more vertical room to lift drum out. once drum was out, i used a snap ring plyers to take retainer ring off to remove damaged rear drum support rollers. replaced both rear rollers. also replaced drive belt and door lamp. the bearing in the left roller had seized and torn a big hole thru the roller . assembled in reverse order. now drum is nice and quiet

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Rear Drum Support Roller Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerJonathan from Meridian ID

Worn wheels, lot of noise

Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Rear Drum Support Roller Kit

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench set

Customeroliver from moss beach CA

Noise and vibration getting louder over an extended period of time

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerChris from Randolph MA

Dryer would turn on and imediately stop

Shut off gas and unplug dryer. Disconnect gas. Take back pannel off by removing a bunch of screws. Take lint trap apart few more screws here. Remove top of dryer (pop the plastic cllips), and front door/panel. Vacume all areas (tons of lint everywhere). Pull out tumbler. Change support wheels. Take off blower fan by using an adjustable wrench and 1/2 " wrench. hold fan with adjustable wrench and turn drive shaft clockwise. Then remove motor. Replace with new motor and reverse the process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-19 of 19