Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2121513
This is a replacement ice maker. This assembly includes the ice mold and the control device. The water inlet valve pumps water into the mold, which stays there until it is frozen solid and ejected into the storage bucket. The process continues until the bucket is full. This replacement part does not include the cover, shut off arm, wire harness, or the mounting hardware. You will need to use the existing pieces, or order those separately. You will need a nut driver to successfully install this part. Unplug your appliance before you begin any repair work.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.Unplug appliance.Remove timer cover by hand pressure @ edge.Remove single attachment screw & bracket at lower front of icemaker.Disconnect wiring harness from socket @ rear of compartment.Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.A good push of the new unit towards the snap-ins along with some upward force will get it stable.Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.Dump the first couple of batches of cubes just to make sure you're free of any residue.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the failed ice maker and performed a post-mortum to detemine the root-cause of the failure. Removal began with me reaching behind the icemaker and disconnecting the power to the icemaker. Then I removed the single screw that attached the supporting "L" bracket located on the bottom of the icemaker unit. I then carefully lifted the bottom of the icemaker away from the wall. This move disengaged the two plastic latching features that anchored the top of the icemaker to the refrigerator wall. I could then pull the unit out so that I could inspect it for the problem. I have had experience with failed icemakers of similar design in the past and there is a fundamental weakness in their design. The small electric motor that is used to activate the various steps involved in making the ice moves a set of copper finger contacts around a circular track. During this movement, these contacts frequently make and break the electrical circuit that turns on the small heating element that is used to lightly thaw the ice so that the extraction fingers can more easily sweep the latest batch of ice cubes from the ice making tray. This making and braking of contacts can occur several times a day. Over the lifespan of the icemaker, this making and braking of the contacts erodes the contact fingers and also builds up a residue of carbon that ultimately results in the loss of electrical contact between the fingers and the copper track that it normally rides upon. Once the electrical contact is lost, the icemaking process comes to a grinding halt.Installing the replacement icemaker was a breeze. I just reversed the order of the previous steps and after reconnecting the power cable to the icemaker, it was back in the icemaking business. Of course there was a waiting period of approximately one hour before any ice was forthcoming since the new icemaker had to cold soak before it was ready to make the first batch. It has made ice consistenly since the installation.
replaced witha new ice maker and It works but does not nake the ice as fast as the old one? any sugestions?ED. Get answers to your repair questions at our forums, forums.partselect.com.
unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Parts were available at the locat applicance store, but the cost was 20-25% higher than ordering through Parts Select (including shipping) + it was delivered in 3 days right to the house.Removing and replacing the ice maker was fairly straight forward. Tight quarters to work in, but managable.1. With the freezer turned off, uplug the ice maker power cable at the back of the freezer. 2. Remove the four phillips head screws and ice bucket rail to the side of the freezer. I found it was easier to re-install the new ice maker with the rail clear off. 3. Loosen the two upper hex head screws holding the ice maker (requires a nut driver).4. Lift the ice maker up and off of the upper screws.5. With the ice maker out of the freezer, remove the power cable from the old ice maker and re-install on the new ice maker. At this point, both the front cover and the on/off lift bar can be transfered from the old ice maker to the new one.6. Slip the new ice maker down over the two upper screws making sure the lower mounting tab is behind the ice bucket rail. Make sure the hole on lower mounting tab lines up with screw hole. 7. Re-install the ice bucket rail and tighten all screws. Make sure the water supply tube is lined up correctly feeding into the ice maker. 8. Re-connect ice maker power cable at the back of freezer and turn freezer back on.It took about 4 hours for the first ice to generate. It cycled normally after that. No more leaks or ice globs in the ice bucket.
Installed new ice maker. It was easy - loosen two screws and unplug old wire harness. Put new unit in place. Did not realize new unit would not come with wire harness, but transferred old one to new ice maker (easy) and, "voila" some ice in 24 hours -- much ice since then. I am a 68 year old woman and it was "sort of fun" doing this job.
I didn't know what the plastic was - just that it was unappetizing. Reading other posts, it must have been the teflon coating. The refrigerator is 13 years old and reading other posts, I guess I'm lucky it lasted that long.My boyfriend did the repair and here is his story: The first ice maker we received was cracked on one corner. Not knowing how it got that way, I was concerned that there might be additional internal damage and that the unit wouldn’t work properly. Part Select was contacted and a replacement unit was sent with no difficulty. As other reviewers have said, the replacement was quite easy, taking less than half an hour. The only tools I needed were a screwdriver and a nut driver. To begin, unplug the refrigerator and turn off the water supply to the ice maker. Loosen, but do not remove, the two top attachment screws. Then remove the bottom screw. Lift the unit up off the top screws and remove the water inlet hose at the top right. It’s probably a good idea to have a container handy to catch the small amount of water that comes out, but you’ll need a third hand for this. The electrical wiring harness is very short and may be tricky to disconnect. On my refrigerator there is a round vinyl connector that plugs into a receptacle on the back wall of the freezer compartment directly behind the ice maker. This was removed with no difficulty (accidently, actually). Once the unit is out of the refrigerator you can remove the connector from the ice maker by using a screwdriver to depress the latch tab that is visible in a window in the unit housing. When installing the connector in the new unit make sure it is fully seated. Next, reconnect the round vinyl connector to the receptacle on the back wall of the freezer compartment. This was the worst part of the whole procedure. You have to support the unit close to the back of the freezer (due to the short harness) with one hand while inserting the connector with the other. This requires both arms in a confined space. The first time I did it I apparently didn’t get a good electrical connection on one end of the harness, and it didn’t work. Because the connectors are directly behind the ice maker I had to remove the unit and re-install it, but it was much quicker the second time, less than 10 minutes. Once the connectors are in place put the water inlet hose into the opening at the top right. You may need to re-use the retaining clip from the old unit for this. Slide the two top mounting ears down between the screw heads and the back wall of the freezer compartment and tighten the screws. Then install the bottom screw. Plug in the refrigerator, turn on the water and make yourself a frosty beverage. All in all, a relatively quick and painless procedure.Another note - we kept saying "is there ice yet"? I think the metal bar that controls the ice maker needed to be raised and lowered a few times before it would work properly as it seemed to raise 1/2 way but the ice would not drop so I put it down and it worked its way up. Had to do it a couple of times over a 4 hour span but once going, it is working like a champ.
I found a similar problem in your forum and desided to give it a shot. The evaporator fan had stop working. It took me a while to find it but I discovered it inside the bottom drawer. I took off the drawer to make it easy to get to. I took off the back cover and there it was. I unplug it and replaced it with the new one which did not look like it at all but since it was the one that I received I pluged it and it worked. I was very satisfied. Thank you again for helping save money.
First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.
First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy. I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me). My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments. Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle. Hallelujah! I now am free for the next challenge! HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.
Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.
Pantry Cover: I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.Ice Maker:I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), slide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.
The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast. I had already removed the old ice maker in order to get the modle number. I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!! I would definatly use partselect.com again.
The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.The new one was so quiet, I thought it didn't work!Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!Thanks!!!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.