Quick Question!

Have you ever purchased from PartSelect.com before?

2121513-2-S-Whirlpool-D7824706Q-Replacement Ice Maker
2121513-2-S-Whirlpool-D7824706Q-Replacement Ice Maker 2121513-1-S-Whirlpool-D7824706Q-Replacement Ice Maker 2121513-3-S-Whirlpool-D7824706Q-Replacement Ice Maker http://www.partselect.com/Schematics/Maytag/50671.gif

Replacement Ice Maker

PartSelect Number PS2121513

Manufacturer Part Number D7824706Q
Manufactured by Whirlpool

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Leaking.
  • Ice maker won’t dispense ice.
  • Ice maker dispenses too little ice.
  • Ice maker dispenses too much ice.
  • Will Not Start.
  • Won’t start.
  • Compare At

    $116.87
  • You Save

    $19.48
  • Your Price

    $97.39
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 251 reviews What's this?
76-90 of 251
 

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Dennis from Goshen, OH

No problems.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: James R. from Laguna Beach, CA

My ice maker wouldn't make ice. The heaters shorted out and fried the wiring and little motor.

Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day or 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.

Jim

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Frankie from Panama City, FL

Cracked ice maker causing leak

Removed old ice maker, had to use the wire shutoff from old ice maker installed new one. Very easy repair, very nice product cheapest price on internet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Bradley from Cosmopolis, WA

Ice maker stopped working-fridge failed to defrost and stopped cooling in both compartments.

I popped out the side panel to the right of the ice maker and removed the ice tray-then used a nutdrive to remove the screw under the ice maker. Lifted up on the unit , dropped it down and used a flat head screwdriver to press the tab in on the electrical connector at the rear-then removed the unit from the Freezer. The end cap that covers the controls on the old unit snapped off easily as did the small metal tab (both needed to be placed on the new one) and I re-installed the new ice maker doing the reverse of the removal. Watch to make sure that the white rubber water line goes back into place as you remount the ice maker in the Freezer.

As for the thermostat, I loosened the temperature control cover in the top of the refrigerator by pulling down on it, needed to pull out a bit to clear the control levers-easier if they're centered on the 5. I removed the retaining screw in the center of the rear of the cover using a nutdriver, and that lowered the cover enough to remove the screws that held the thermostat assembly in the upper right (also using the same nutdriver that worked on everything else). I removed the electrical connector from the old thermostat and attached it to the new one. The old thermostat didn't have a cover on it like the new one, and it was easier to make sure that the electrical connector was attached by popping the cover apart-attaching the connector, and then snapping it back together. The new unit snapped into place by pressing down firmly, then I re-assembled the cover plate doing the reverse of the removal.

If you don't count the two hours that I spent defrosting the freezer coils with a hair dryer-these were FAST repairs, and the refrigerator is running like new again

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Jacob from Garland, TX

Wouldn't make ice

unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: KEN from FOUNTAIN HILLS, AZ

Original ice maker was leaking

There are 3 screws holding the icemaker in place. After removing the ice bucket, I removed the screws, then twisted the unit to gain access to the power plug. The plug is held in place by a plastic flap which is part of the connector. It has to be pushed down to remove the connector. The new unit went in perfectly and performed flawlessly for 3 days until the compressor blew out! After feeling some sense of accomplishment having fixed the icemaker, I learned that my neglecting to clean the vent grill in the front of the refrigerator had caused its demise. Don't forget to clean the dust out of the vents!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Walter from Hampstead, NH

The old unit had teflon flaking off into the ice

First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Jim from Gainesville, TX

Water leaked into ice bin causing big ice chunks

I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Jon from Leander, TX

Black flecks in the ice

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: John from Lake Worth, FL

Simple to install -

Removed old icemaker by removing two hex screws and one phillip's head screw.

Disconnected power connection to refrigerator.

Removed power connection harness and ice level sensor arm/levor and cover from old ice maker and installed on new ice maker.

Re-installed in refrigerator. It was simple on this model.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Brian from Brunswick, GA

Leaking icemaker and dispenser

First I removed the 4 Screws that held the dispenser in place and after removing it , it was a breeze to put back, just be sure to get the spring back in place and tight to hold the door in place. The icemaker was not much harder other than after removing the one screw and the end cap, it was a little difficult to get off the bracket , but managed to free it , other than that it was ok to remove and replace. All in all this went really easy , a lot better than I thought it would.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Albert from Pampa, TX

The task itself was simple, the freezer being on the bottom of refrigerator made it difficult for a 84 yr. Man to get to. It did take a long time for the icemaker to kick in..

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Steven from Clinton Corners, NY

Replaced ice maker

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Joseph from Altadena, CA

Ice maker stuck, leaky, broken stop bar

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
  • Replacement Ice Maker
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Loren from Indianapolis, IN

Ice maker leaked creating an ice block

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

76-90 of 251