| |
11 of 13 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerJames Richard from St. Cloud MN
Light switch broke
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerRichard from New Castle PA
Switch light didn't work; broken drawer cover hinge
I removed the switch assemble from the panel with a Swiss Army knife. Disconnected the two wires and reversed the process with the new switch. Not being all that handy, I assumed the job would be very involved, but was very pleased that it was nearly effortless. A less than 15 minute operation.
Removing the right side panel of the lower drawer was a slightly more involved, requiring the removal of 3-4 screws and replacing the inner workings of the temperature adjustment workings on the new panel. But it proved pretty simple and only required about 20 minutes start to finish.
|
2 of 2 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from East Meadow NY
Light not working in fridge
It was so easy!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
|
1 of 1 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
Customerstu from richmond VA
Fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Socket set
CustomerDave from Manchester Center VT
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerStanley from Santa Cruz CA
Light switch broken; door bin broken
I removed the broken door light switch by inserting the flat end of a butter knife along the right side of the old switch. This depressed the tab that holds the switch in place, and the switch popped out. I tranferred the two slip-in wire connectors from the old switch to the new one and pushed the new switch into place. It was quick and easy. If you examine the new switch, you will see how the squeeze-tab works and how you need to release its tension to remove it.
The door bin just slipped into the holders from above.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTHOMAS from WILLARD OH
Defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerGail from Golden CO
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
|
0 of 1 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Wrench set
CustomerRonald from Billings MT
Non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
|
0 of 1 people found this instruction helpful
Parts Used
-
- Light Switch - 2 Terminal
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJoseph from Destin FL
Light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
|