2100169-1-S-Whirlpool-99002838-Door Latch Handle
2100169-1-S-Whirlpool-99002838-Door Latch Handle 2100169-2-S-Whirlpool-99002838-Door Latch Handle http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/53051.gif

Door Latch Handle

PartSelect Number PS2100169

This handle latch is bisque in color and is made of plastic.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door latch failure.
  • Compare At

    $37.88
  • You Save

    $6.31
  • Your Price

    $31.57
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Latch Assembly with Switches- NO Handle

Part Number 2099682

This part comes with the two door switches but does NOT include the handle. *** Handle sold separately.

Order within the next 3 hrs and your part ships today!
$82.82
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 8 reviews What's this?
1-5 of 8
 

6 of 7 people found this instruction helpful

Parts Used

  • Door Latch Handle

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJerry from Hot Springs Village, AR

Door latch

I removed all the screws from inside of the door. I disconected the two wire harness and removed the door latch. I replaced it with the new latch. Put all screws back in the door. Every thing works good. It was vary easy to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Door Latch Handle

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerLee from Deltona, FL

Handle broke at pivot points

Turned 120 v breaker off at power panel, removed 8 torx head screws from door panel removed old handle and snapped in new, replaces screws, flipped breaker back on. About 10 minutes tops using a battery driver.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Door Latch Handle

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDAVID from EARLHAM, IA

Broken handle

New handle came out of the package and was fully installed in 5 minutes. Couldn't be easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Door Latch Handle

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

Customerraoul from victorville, CA

Door would not open

remove door panel screws 8 of them.door lock and switch are one unit.pull off wires in order to replace door handle.slip wires back in place and replace door panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

CustomerThomas from INDIALANTIC, FL

The door latch mechanism was broken, thus preventing the diswasher from operating and sealing properly

First, shut off power to the dishwasher. Remove the stainless outer panel from the door to expose the latching mechanism and control board. Remove the latch mechanism from the inner door panel (if plastic pin holders are still intact) and place off to side. No need to disconnect wires. Remove the control panel by taking out hex head screws and snapping out of retainers on old control panel. Again, no need to disconnect wires; let the board hang out of the way. Remove old control panel by removing hex head screws. Replace with new control panel. Snap control board back into place and secure with hex head screws. Be sure it is seated properly. In my case the door latch handle was also broken. Simply snap new one back into latch mechanism. Replace outer stainless door panel with torx screws and you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8