2100167-1-S-Whirlpool-99002836-Latch Handle
2100167-1-S-Whirlpool-99002836-Latch Handle 2100167-2-S-Whirlpool-99002836-Latch Handle http://www.partselect.com/Schematics/Maytag/53051.gif

Latch Handle

PartSelect Number PS2100167

This latch handle is black in color.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door latch failure.
  • Will Not Start.
  • Compare At

    $41.16
  • You Save

    $6.86
  • Your Price

    $34.30
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Latch Assembly with Switches- NO Handle

Part Number 2099682

This part comes with the two door switches but does NOT include the handle. *** Handle sold separately.

$83.73
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 22 reviews What's this?
1-5 of 22
 

22 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Robert from DuBois, PA

Door would not latch

simply remove the ten screws, lift up the inner door. Disconnect the four electrical prongs on the latch assembly. Connect the new assembly and replace screws. Very simple. Saved 100 dollar service call

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set
Customer: Joseph from Dover, DE

Touch pad inoperable and latch hande & latch broker

Disassembled inside door and replaced sensor board and latch devide and handle. I removed all the screws on the inside of the door, released the circut board(sensor board or control board) and removed each connection one at a time and pluged them one at a time into the new board. I studied the setup before I disconnected anything. Oh yes, I turned off the breaker in the basement before opening the panel on the inside of the door.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 11 people found this instruction helpful

Parts Used:
  • Latch Handle
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Robert from Ocala, FL

Squeezing the handle did not open the latch

After unplugging the dishwasher, I opened the door which required more pulling effort than it should. There were 10 screws which fasten the inside panel to the door. 2 Of these are located next to the latch. I used my drill driver with a star bit. By carefully separating the panel from the door, I was able to see the inside of the latch mechanism. The plastic handle had 2 ears that had snapped off. It was fairly easy to remove the broken handle and replace it with the new one. All that was necessary then was to replace the 10 screws and tighten them. It seems to be fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools:
Customer: Michael from Silverdale, WA

Plastic bezel broken

1 - Unlugged power cord.

2 - Reviewed main plastic panel to see where required screws were located.

3 - Removed 8 screws on inside stainless panel.

4 - Separated the loose panel while removing screws holding the front plastic bezel in place. Removed two screws hold latch in place.

5 - Noticed that two screws were holding the PC board down plus a retaining nub on the plastic piece. Removed screws and held PC board out of way.

6 - Pulled off plastic splash shield held down with sticky gunk.

7 - Was a little difficult keeping the front door panel separated from the inside panel while doing all the work.

8 - Installed new handle into latch device and then attached to inside of door.

9 - Put it all back together twice after forgetting to install the two PC board screws. Oops.

10 - Felt confident the repair was correct when done.

Parts arrived as promised. Web exploding details insured exact replacement part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used:
  • Latch Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Glen from Bala Cynwyd, PA

Handle ends broken

1. Removed the torx screws around the metal liner
2. Pulled back the metal liner being careful not to disturb the connected wires
3. Pushed scissors into the latch actuator (part that pushes into the the catch on the dishwasher cabinet) until it sprung into position to simulate closure - you can't get the handle on easily without doing this.
4. Placed the end tab of one side of the handle into the slot on the side of the latch actuator.
5. Applied pressure on the other side until it snapped into place.
6. Pulled on the handle to release the catch.
7. Replaced the torx screws.
8. Works perfectly!! (until it breaks again)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 22