2099941-1-S-Whirlpool-99002589-Bottom Door Seal
2099941-1-S-Whirlpool-99002589-Bottom Door Seal 2099941-2-S-Whirlpool-99002589-Bottom Door Seal

Bottom Door Seal

PartSelect Number PS2099941

This part is sold individually and does not come with push nuts. Must order the push nuts separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $22.09
  • You Save

    $3.68
  • Your Price

    $18.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Seal

Part Number 2099940

It provides a waterproof seal between the tub and the door.

$47.45
In Stock

Push Nut (Stainless)

Part Number 2100091

Sold individually.

$12.32
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 3 reviews What's this?
1-3 of 3
 

17 of 22 people found this instruction helpful

Parts Used

  • Bottom Door Seal

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerBrooke from Edmond OK

Leaking dishwasher

I first replaced the door seal and that did not stop the problem but noticed two little seals on the door. They were terribly worn so I unscrewed the door and cut the little washers that were holding the old ones in place. I replaced the seals and put the cut washers back on (I didn't have new ones) and it was done. All is well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerMitchel from Camden SC

The seals were deteriorated at the lower part of the door and allowed leaks. The door latch broke out twice, so replaced whole handle mechanism this time.

The repair is simple open the door and remove the perimeter screws and lift the door panel up. Be careful of attached wires. The handle only requires that you remove two electrical connectors and reconnect to the new latch handle and realign it with the screw holes in the door panel. The seals are not as easy to change they are attached with spring clips that I had to snipe through to get the old seals off. The new seals did not come with new spring clips, so I flattened the clips and reused them, they did not hold as tight, but seemed to work. Then just reinstall the panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customerglenn from kirtland OH

Broken handle/latch that locks door

anterior door, star allen set to undo, hot/neutral wires. will disconnect with some difficulty, ok to break. new latch is a large complete unit with new hot/neural wire attachments.
The snaps that are apart of exterior of maytag are likely broken if the latch is but the anter start screws keep it more than stable.
reassemble anterior with screws.
its a good idea to order and replace the rubber corner door seals at the same time if the unit is some yrs old. very easy. they will snap off/on.

this unit is a deluxe maytag 2006 model. white

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3