2099940-3-M-Whirlpool-99002588-Door-Seal.jpg
2099940-3-S-Whirlpool-99002588-Door-Seal.jpg 2099940-1-S-Whirlpool-99002588-Door-Seal.jpg 2099940-2-S-Whirlpool-99002588-Door-Seal.jpg

Door Seal

PartSelect Number PS2099940

It provides a waterproof seal between the tub and the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $56.94
  • You Save

    $9.49
  • Your Price

    $47.45
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Bottom Door Seal

Part Number 2099941

This part is sold individually and does not come with push nuts. Must order the push nuts separately.

$21.38
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 12 reviews What's this?
1-12 of 12
 

9 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerJohn from Warren MA

Door leaking, handle broken

Door gasket was easy out and in using the white mark on the seal to line it up with the center. The latch came with the handle so I returned the extra latch assembly that I ordered. Super easy to install. Removed door screws, carefully lifted and set aside inside of door leaving wires attached. Reved wire from latchtch switches, attached wires to new latch, put in postion and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerROY from SUFFOLK VA

Door leaks

Replaced the door seal. Removed the old seal and gently stretched the new seal and pushed it into the channel. Snipped off about 2 inches excess seal. As far as the Inner Door Foam Insulation Strip goes, it was not as easy. To begin with, the old Foam Strip was attached to the door insulation and not the door. The attempt to remove the old Foam Strip from the insulation became cumbersome, so I just attached the new Foam Strip on top of the old Foam Strip. So far, after a few cycles, it appears that it corrected the leak.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerEric from Ellensburg WA

Door latch and seal not working correctly and broken

Removed the screws holding the door liner in place removed latch. Waited for half of the parts to get here, about 2 weeks. Parts got here except for Door latch and seal they were back ordered. One month after I ordered all parts finally arrive. Replace door latch assembly and replace door seal reinstall retaining screws....Done works good again. Parts were all the correct ones just took a long time to get here.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

Customerkimberlee from plains TX

Leaking at bottom front left corner

removed the cover to remove the door seal then replaced it with the new one and replaced the insulation strip

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Door Seal

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerEric from Overland Park KS

Humidity would seep out absorbing into the granite above

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerJohn from Holllis NH

Dishwasher was leaking during wash cycle out the front door

Replaced the door gasket, inner foam strip and the bottom seals on the door. Unfortunately I broke the plastic door latch handle in the process and had to purchase a complete latch assembly too.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerAdam from Lincoln NE

Latch handle broken, leaking water.

Removed 11 T20 Torx head screws. Removed and replaced latch. Removed and replaced door seal and foam insulation strip - no additional tools required. Super easy to repair and didn't leak a drop afterwards.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Door Seal

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRonald from Chester Springs PA

Dishwasher leak from door seal

Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Seal

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerWilliam from Interlochen MI

Worn out

simply pulled out old one slowly inserted new one (stretching slightly) Presto done

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Door Seal

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerPhyllis from Grass Valley CA

Dishwasher leaked out of bottom

I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerLisa from Plainville CT

Door handle snapped when pushed to open; seal dirty

I am not the one who typically fixes our appliances, but I do frequently research for the part. This site is by far the easiest to navigate; the part I needed was clear; they recognized my model immediately; part arrived the next day without expedited shipping costs. Will use this site for all of my appliance part needs.

Gasket pulled right out and new one placed in; handle latch-unscrewed door inner panel, pulled out old part and reconnected new part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDenise from Pine City MN

Outside handle of door latch brocken

removed the door front by removing screws. Unhooked old latch from electrical prongs and installed new. Replaced screws. Removed old seal and installed new

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12