| |
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers, Socket set
CustomerAlma from Demotte IN
No spray inside dishwasher, dishes still dirty
Removed spray arm from bottom of dishwasher, Then three torx screws holding housing and filter screen together. Next the 5/16 screws csme out and I founf the broken pump impeller pieces. Took the 5/16 screw out of the broken impeller hub and pryed the broken hub off the shaft with two screwdrivers. Be careful not to break the housing when taking off the broken hub. (hardest part was getting the broken piece off). Also went deeper and replaced the drain pump impeller ( which was not broken) and the seal assembly. re assembled in reverse order. Repared a broken wheel on the top rack too. Unit works great. Thanks for the fast service and valuable info for the home repair person
|
0 of 1 people found this instruction helpful
Parts Used
-
- Wheel Mounting Strip Only - NO Wheels
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from San Ramon CA
Upper rack sagging from broken wheel mount
Removed the white mounting strip on the right side of the upper dishwasher rack by aligning the v-shaped slot. Note that one slot that's aligned with the "v" and push that part through the slot. It will take a slight downward twist to align the second slot, then push that slot downward as well.
I popped the mounting strip from the wheels (the front mount on the mounting strip was damaged to it came out easily). Put the mounting strip back in through the "v" slots (reversing the above direction starting with the slot that aligns at a slight angle first), then snapped the wheels back into the mounting strip.
One note when ordering is that the picture shows the strip with wheels, but the strip came without wheels. Fortunately, the existing wheels worked OK, but be aware that you should order the wheels separately if they're damaged as well.
No tools required and the only tricky part was figuring out now to get the "v" in the mounting strip aligned with the slots (and doing it in the right sequence.)
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerScott from Budd Lake NJ
Wheel mount wore out
removed the rail stops and pulled the upper shelf out completely. pulled off mounting strip and removed wheels. put wheels on new strip and put back together
|
0 of 1 people found this instruction helpful
Parts Used
-
- Wheel Mounting Strip Only - NO Wheels
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRebecca from Spooner WI
Mounting wheel strip has been bent for a couple years, rack would not roll properly.
Unbelievable easy! Pulled out the rack, used a flat screwdriver to pry off the old rollers, installed them on the strip, put everything back in place--works like new! Can't believe I put up with the bent strip for a couple of years when it was such an easy fix!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Wheel Mounting Strip Only - NO Wheels
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
Tools
CustomerMaria from Voorhees NJ
Top rack right side bracket was broken - causing rack to close wrong - this caused a leak
took rack out by unsnapping things in front of rack - it took a few minutes to figure out how to replace the part - then I removed the rack then the wheel mount strip - removed the wheel from old wheel moun, replaced them on the new one reinstalled the shelf, replace part to hold shelf in place and that was it. Very easy no repairman!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Wheel Mounting Strip Only - NO Wheels
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKARIN from PHOENIXVILLE PA
Wheel broke off of strip
Removed the broken strip, carefully took the wheels off, put the wheels on the new strip and put it back on. Easy peezy! I was nervous ordering from an unfamiliar site that didn't have paypal but found it to be FANTASTIC! Part came FedEx on a Saturday with basic shipping purchased. I will check here first for all appliance repair in the future.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerNoel from Hamilton VA
Wheel and support assembly fallen apart
Snapped into place after about 5 minutes of study. Easy!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMarvin from Chatsworth AL
Broken wheel mounting strip
replaced strip bar and wheel...saved the price of a complete upper rack
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customercheryl from brandon MS
Upper tray wheel strip broke. Lower adjustable plate rack clip broke
The most difficult part of the repair was to figure out how the two retaining clips at the end of the rack slides came out. Once those were removed, it was a simple matter of replacing the broken wheel mounting strip with the new one. A simple "place and clip-in repair process."
As for the repair of the adjustable clip. A simple "snap-in-place"repair was all that was needed.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerJames E. from Presque Isle ME
Rack on the dishwasher would not stay in place.
Received the parts, installed, and now works fine. f
Fast service, great price.
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
CustomerJohn from Roy UT
Top tray had broken wheels
removed old rail replaced wheels and was good to go
|