2099288-1-S-Whirlpool-99001795-Drain Cover
2099288-1-S-Whirlpool-99001795-Drain Cover 2099288-2-S-Whirlpool-99001795-Drain Cover 2099288-3-S-Whirlpool-99001795-Drain Cover

Drain Cover

PartSelect Number PS2099288

This covers the drain impeller and won't allow larger particles through to the impeller/motor/pump area.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

SCREW

Part Number 2057900

$4.46
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 1.8 / 5.0, 2 reviews What's this?
1-2 of 2
 

9 of 12 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Wrench(Adjustable)

CustomerYuriy from Skokie IL

No pressure in spray arms, no washing action

The hardes part was to remove the retaning nut (#34 on the diagram). There isn't enough grab on it and it is quite flimzy. Be prepared to butcher it if necessary. I resorted to wedging a screwdriver between the top flange of the nut and the spray arm and that gave me torque I needed to undo it. Luckily, the nut survived and could be reused.
Once the nut is off, everything else is pretty straightforward, just pay attention what goes after what and in what orientation (take notes if you must, however, I did not and got away with it). My machine has not been serviced in years and there was calcium deposits everywhere. If your machine is just as bad as mine, I strongly suggest to remove everything that can be removed and give it a nice vinegar bath or use other products designed for calcium removal (ask your wife what she is cleaning the bathroom with, it will most likely do). Bottom line, the cleaner the parts are, the better it will pump.
In my case, it was the calcium that eventually killed the impeller #14 and made it spin on the shaft (no pumping therefore).
Inspect all the parts for heat / wear damage so you put one order for everything you might need.
Secondly, the screw #12 that holds the impeller #14 on the shaft is a tiny screw and it is originally secured with a threadlocker. Make sure that the internal thread in the shaft and the screw are absolutely dry before applying loctite.
Thirdly, there is a plastic ball that sits in the cavity in one of the disk-like part (not shown on the diagram). Do not loose it and make sure it is put back.
That's pretty much it. Once properly cleaned and repaired, the machine washed like brand new. Pretty good for less than $50 investment in parts and a week downtime. . .

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers

CustomerRobert from Tabernacle NJ

Heard noise shorty after starting to run. Seemed to get worse at times in short time frame

Located circuit breaker for dishwasher and turned off breaker to secure power going to unit. Removed water spray bar arm inside dishwasher basin by unscrewing center nut and unclipping tabs against arm. Removed sheet metal access panels on bottom front of unit. Removed two individual plug in wires to temperature thermister. Removed 4 conductor plug wiring going to motor. Removed ground wire going to motor frame. Located plastic handle which cam locks motor / pump assembly into place. Pulled handle down gently to unlock from detent and turned clockwise to release pressure on assembly. Removed motor / pump assembly from dishwasher enclosure. Installed all new parts purchased as listed above utilizing parts breakdown aquired from PartSelect.com. Reinstalled motor / pump assembly in reverse order as listed above. Tested and ran unit with no problems. Thank You PartSelect.com, Robert.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-2 of 2