Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2099053
This rack comes complete with four attached wheels and the rack may differ in appearance, but will function same as original part.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
Just took the racks out installed the new ones in no tool required.I will go through partselect.com again. Had a very good esperience with them.
Help other customers find the most helpful instructions.
Were these instructions helpful?
The bottom rack was easiest, just picked it up out of the dishwasher and moved the sprayer and the silverware holder from the old rack to the new rack and set it back in the dishwasher. The top rack was a little tricky, it took a minute to figure out to remove the little end-caps on the runners and then it just slid out. Slid the new one in, replaced the caps and moved the upper rack basket. It took less than 15 minutes to fix and now it's like a brand new dishwasher!
Read the experiences here, very helpful. Bottom slides out first - really easy. The new part comes with rollers, you don't need to remove the old ones. Now the only problem, getting the sprayer off the bottom basket. Look carefullty, you must use a screwdriver to release one side of the sprayer, then it works off easily. Make sure you note the orientation of the base of the sprayer. Reverse steps above and you are done. New tray slides in. Our new tray was a bit wider than the old one so we needed to use a bit of pressure to "shrink" the back just a wee bit. The upper is easy also. Since the rails are uneven, make sure you put the high rollers on the high side no matter what your wife told about how it is supposed to go in. The end caps snap inward and slide out of the rails. Easy once you know. The uneven rails are obvious once you notice. Total time was 45 minuts, 30 of which was figuring out how to get the sprayer off without damage.Would be nice to know the factory recommendation for removing the sprayer.
First I did the top - getting the ends off the track is simple, flip the ends "open" like a book on each side, and remove the caps. Pull out the rack, replace with the new one and replace the caps. Bottom rack was easier once I figured out how to remove the spray tower. Grab it firmly and twist. Place it in the new rack, and roll it into the DW. I'm a fairly handy woman, and this was quite easy.
Most difficult was figuring out how to release the top rack...just flip the end pieces to the side and out they come. Next was removing and reinserting the spray head in the bottom rack...just twist and take out then align and twist into place in the new rack.
Replaced upper and lower racks. The new lower rack has a design flaw: it has 3 wheels on each side, but should have 4 wheels on each side. When you pull out the bottom rack, the last set of wheels drop down into the open space where the door hinges to the cabinet, causing the dishes to bounce and shake around. Then when you push rack in, you have to lift it back up onto the tracks made for the wheels to roll on. You can't pull the bottom rack out far enough to access the back of the rack very well.
With a straight edge screwdriver I carefully removed the plastic end caps on the rack support glider-shelves, replaced the old rack with the new rack, and then reattached the end caps.I felt better about ordering the part Online after having talked to a sales person since there were several racks from which to choose. She reassured me that I was ordering the correct part number. I am a woman and 62 years of age, and I was pretty sure this installation would be a no-brainer. I just wanted to make sure I had the right part for the job.
Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.We will recommend your site to friends.
Although the (top) dishrack assembly included the nylon wheeles, it was easier to replace the old one by disengaging it from its wheels and installing the new rack on the old wheels kept in the slider track. The snap hook that held each wheel to the old rack was popped loose (finger pressure) and the old rack removed. The new rack was held in place and each of the four wheels snapped to it. Each wheel fits into a wire post on the basket and the plastic hook snaps onto the wire frame. The most difficult part of the 'repair' was removal of the handle from the old silver ware basket. I used screwdrivers to simultaneously pry the four tabs of the halde out of the slots on the basket and pulled (hard!) the handle off. It snapped easily into place on the new basket.
Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days. Great service. Jack
Removed screws on the inside of the dishwasher - removed interstainless cover - disconnected wiring harnesses - accidently pulled terminal loose from control board - cut wires to terminals-took control board out - resodered terminal - used wire nuts to attached cut wires - attached wire harnesses - installed intercover - replaced screws - tested dishwasher - all okay.
Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.
First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.
Just undid the brackets holding the top rack in place and put in the new racks, locked the brackets and in the bottom put the water tower on and slid that rack in place, and bam we were ready to turn it on. It's wonderful, all new and clean. LOVE IT!!!
I removed the bottom rack by simply rolling it out of the dishwasher, and removed (unsnapped) the rotating spray assembly. It was easily snapped into the center of the new dishrack. Next, I removed the roller stops from the rail holding the upper dishrack by following the marks (arrows) on the stops. I rolled out the upper dishrack, and rolled in the new one. Finally, I snapped the roller stops back into position.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.