| |
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Wrench set
CustomerRobert from Flushing MI
Spring assist on door failed,
Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerDavid from Philadelphia PA
Dishwasher door was slamming down, heavy to close
Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerBasil from St. Charles MO
Door heavy, would not spring up.Broken link.
Pulled D/W out about 1/4 of the way. Kept door latched at all times. Replaced plastic links with new ones. (one was broken but replace in pairs!). Attached springs. No tools required for this. Pushed D/W back in place and secured screws to top. Only tool used was a nut driver to remove the screws holding the D/W to the counter. Total time 7 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Wrench(Adjustable)
CustomerCarol from Malvern PA
Our 14 year old maytag dishwasher needed new springs for the door
We hired a handyman, who recommended we go online to order the parts. They arrived
at my door in less that 24 hrs! Luckily, the handyman was back the next day as well, and
he installed the new springs and spring linkage.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerwilliam from Attleboro MA
Plastic door spring part broke
I went at it wrong to start. Then I figured out creating the proper angle that mirrored the normal operation was the trick. I tied a string on to the spring with the plastic part attached then the other end to a hook. I pulled the hook at the correct angle & the plastic part was lifted to its slot. Pushed it down into the slot & cut off the string.
Took about 2 minutes that way.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerMatthew from Whitman MA
Dishwasher didnt stay running/ door falls to ground
Removed the inside door cover.Next remove door handle/latch/switch assy. Replace assy, replace covers. Done. Door spring linkage, pull out dishwasher to access sides. Insert linkage into spring hook, and install hook onto dishwasher bracket. Or just watch the video.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerHenry from Columbus WI
Door wouldn't open slowly
I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.
|