2097827-1-S-Whirlpool-912652-Door Spring
2097827-1-S-Whirlpool-912652-Door Spring 2097827-2-S-Whirlpool-912652-Door Spring

Door Spring

PartSelect Number PS2097827

This door spring is sold individually and is located on either side of the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door latch failed.
  • Leaking water.
  • Compare At

    $4.51
  • You Save

    $.75
  • Your Price

    $3.76
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Spring Linkage

Part Number 2097828

This part provides more flexibility for the door spring.

$3.51
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 9 reviews What's this?
1-9 of 9
 

22 of 25 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench set

Customerkathleen from farmersville CA

Son used door for a step and bent as well as broke spring door component

first i removed the 2 holding screws fron the underside of the counter then oulled the dishwasher out about a foot. i then removed the side panel that hold the front plate in plase on the right, below this were the screws that held the door hinge assembly on the right. i then proceeded to remove those bolts. and replaced with the new one. replacing the spring and the linkage came next no tools required. i have to say that the diagram when i ordered helped emensly. i am a 45 yr old woman and fixed it by nyself thanks to your ordering diagrams. life is good!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Wrench set

CustomerCharles from Melrose Park IL

Water leak from bottom of door, and broken door spring linkage

Thanks to repair stories about door leaks on partselect.com I ordered parts for the detergent/rinse dispenser in addition to the door gasket. The installation of the door gasket is really easy, simply remove the old gasket starting at one end. I needed a small screwdriver to get the old gasket end out of its channel, then pulled the entire gasket out. I cleaned the channel with water and simply pushed the new one into the channel, starting at the left bottom and continuing around. It is important not to stretch the gasket and also to have it equal length on both sides of the tub. Total time less than 10 minutes.

The replacement of the detergent grommet requires removal of the inner door panel. I removed the seven torx-head screws along the edge of the plastic panel and lifted the panel away from the outer metal door. There are wires attached to the detergent cup motor. I tried to remove them but found it was easier to simply snap the motor out of it's retaining clip, leaving the wires attached. The inner door panel can now be removed. The detergent/ rinse aid module is removed by taking out two hex-head screws. It lifted away from the door and the grommet is right on the front, surrounding the detergent cup latch. I removed the old grommet, cleaned the residue of old detergent and water hardness from the latch and the backside of the inner door. and placed the new grommet over the latch. I used a little water on the new one to make it slide on easier. I then reattached the module to the inner door. Be sure the grommet is centered in the square hole and evenly tighten the two hex-head screws. Re attach the soap motor by snapping it in place being careful to align its plunger correctly with the soap module. There is a groove in the plunger that fits into the plastic arm of the module. Re assemble the inner door and tighten the torx-head screws evenly. This job took about 30 minutes and completely solved the leak problem.

The broken spring linkage requires partial removal of the dishwasher. First, I turned off the power and water as a precaution. I removed the undercounter philips head screws, removed the lower access panel and kick plate using a nut driver. To access the door spring mechanism, the dishwasher must be pulled out from the cabinet about 10 inches. I had flexible electric and water lines so they didn't need to be disconnected. If the water and electric are rigid, then they have to be disconnected. This may require a professional. The replacement of the door springs and linkages is very easy once the dishwasher is pulled out. Keeping the door closed and locked, simply hook one end of the spring on the linkage, attach the other end of the linkage to the door and attach the other end of the spring to the hole in the dishwasher base where the old spring was attached. It is a good idea to replace both springs and both linkages to keep equal tension on both sides of the door. Slide the dishwasher back to it's original position and replace the undercounter screws and the lower access panels. Total time less than 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDavid from Mesa AZ

Broken door spring linage and lost spring

Took off bottom plate for access. Slid part that holds bottom of spring forward so I could reach it without pulling dishwasher out of position. Hooked spring to bottom attachment, then connected door spring linkage to holder that is attached to the dishwasher frame. Adjusted the tension with the tension screw and buttoned up bottom plate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyVery Difficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerHerbert from Mechanicsville MD

Tjhe nylon piece that attaches the spring to the door broke.

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFred from Earp CA

Door springs dissconnected broken links

Removed 2 each screws from counter top. Pulled washer out 1'. Installed springs and linkage by hand with door closed. Push washer back reinstalled 2 screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerSamuel from St. Johns FL

Both door springs corroded and broke. Linkage connectors broke also.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBill from Nicholasville KY

Door spring broke letting door fall down

This was really easy. I just took out the two screws securing the unit to the counter top and slid it out about 6 inches. Broken plastic spring linkage was obvious and easily accessible. I didn't know there was one on each side, I would probably have went ahead and ordered both and replaced them at the same time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerCarol from Malvern PA

Our 14 year old maytag dishwasher needed new springs for the door

We hired a handyman, who recommended we go online to order the parts. They arrived
at my door in less that 24 hrs! Luckily, the handyman was back the next day as well, and
he installed the new springs and spring linkage.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerHenry from Columbus WI

Door wouldn't open slowly

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-9 of 9