2097160-1-S-Whirlpool-902894-Door Gasket
2097160-1-S-Whirlpool-902894-Door Gasket 2097160-2-S-Whirlpool-902894-Door Gasket 2097160-3-S-Whirlpool-902894-Door Gasket

Door Gasket

PartSelect Number PS2097160

Manufacturer Part Number 902894
Manufactured by Whirlpool

This door gasket can be installed by simply pressing it into the channel around the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $56.70
  • You Save

    $9.45
  • Your Price

    $47.25
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 97 reviews What's this?
 

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

Tools

CustomerJames from Gulf Breeze FL

Leaking under door during wash and rinse cycles

Removed old gasket and foam strip. Cleaned area. Installed door gasket. Trimmed foam strip to fit and installed.

Leak has stopped!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerPeter from San Jose CA

Leaking door- dispenser door latch grommet

Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerJoAnn from Raleigh NC

Dishwasher door leaking

I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerThomas from Oneida NY

Water leaking out the right side bottom of door.

Very easy to do. Used needle nose pliers just to get a first grip on the door gasket and then pulled it completely out. Pulled up the Water Deflectors by hand. Cleaned the gasket trough with a soft cloth, warm water and dishwashing detergent. Rinsed. Then simply pushed the gasket into the trough, lightly tapping into place, then pushed on the water deflectors, and no more leak!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerPhilip C from Cloquet MN

Occasional water leakage at bottom of door

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerRON from MOUNT AIRY MD

Leak around door

Removed old door gasket and water deflectors and replaced with new. Got the gasket in backwards at first. Removed and rotated 180 degrees and it went in properly. (Used tech video provided by parts select to help me.)

Though the old gasket was definitely bad, water still leaked after replacement.

Key issue ...... over time, contamination has accumulated in the water shutoff lever assembly and also on the shutoff microswitch underneath the internal water float, making both sticky and non-responsive to water level. Water had been overfilling. (probably defaulting to a maximum number of seconds to fill). ALSO - original installation was not totally level, with back of tub higher than the front.

Leveled tub. Removed mocroswitch and lever and cleaned both of sticky grease.

No more leakage.. basic problem was actually overfilling, allowing water to surge into the lower internal door vent upon pump startup.

Ron
Mount Airy, MD

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrank from Ridgefield CT

Lower left corner of the door was leaking every so often.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerPaul from Gibsonia PA

Dishwaser leaked onto the floor

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Carol Stream IL

Replaced control panel to change color / fix leak

The tub seal was worn and leaking, this took 5 minutes to replace. I also changed the color of the dishwasher from almond to black by painting the metal panels and replacing the control panel and knob with black ones. Looks like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerSandra from Paxton MA

Leak bottom right of door

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRobert from Nashville AR

Water leak around door of dishwasher

I removed the gasket from the packaging & soaked it in hot water for approx 5 minutes to enhance the pliability of the rubber. I them opened the dishwasher door and removed the existing gasket, making sure I observed any specifics of the gasket, (ie...shape of gasket). I then cleaned any debris from the gasket channel. I took the new gasket from the water and folded it in half to determine where the middle was, and I started inserting the gasket beginning at the middle area of the channel, (just under the door latching mechanism). I finished inserting both sides and then closed the door for approximately 30 minutes to complete the gasket seating process. No leaks!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRobert from Ledyard CT

Broken hinge on bottom draw

Used your web site was able to identify correct part very quickly. Received the replacement part in 2 days.
Removed broken part with screw gun only took 20 minutes. Was very please with ease of site and quick delivery.
Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJohn from Redmond WA

Water on floor under dishwasher

The problem would rarely happen if the dishwasher was fully loaded vs. lightly loaded; which would produce a lot of water rapidly during the spray cycles. (or empty during the house inspection!). Removing and replacing the door gasket is super-easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJames from Ann Arbor MI

Leaking dishwasher door

I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerGeorge from Whitinsville MA

Leaky door

Removed old gasket and simply replaced it with the new one. Very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?