Door Gasket

PartSelect Number PS2097031

It provides a seal between the tub and the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $64.82
  • You Save

    $10.80
  • Your Price

    $54.02
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 12 reviews What's this?
1-12 of 12
 

23 of 28 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerJeffrey from Wilmington DE

Replace door seal

Remove old seal by pulling out tabs one at a time.

To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 14 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJEFFREY from La Mirada CA

Door gasket leaking-door hard to lift due to broken spring

remove lower access panel to expose spring. remove broken spring with longnose pliers. with door closed install upper hook of spring with nylon bushing on door hinge. using longnose pliers pull down on spring to hook on lower braket.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerMark from Bloomingdale IL

Gasket was leaking

Removed the gasket by pulling it's tabs out of the metal slots in the door. This was accomplished by accessing the inside of the door.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerLarry from Auburndale FL

Leaking around door

cleaned lime and calcium build up off of gasket
and it stopped the leak . yea . parts select was very helpful and said i could return the unused
gasket. . this is a good place to get parts.thanks larry

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJerry from Mason City IA

Water leak lower left, bottom of door

REMOVED THE OLD GASKET. IT WAS EASY TO "POP OUT" THE PARTS THAT HELD THE GASKET IN PLACE WITH A REGULAR FLAT BLADE SCREWDRIVER. BECAREFUL NOT TO CHIP THE PORCLIEN (SP). ANY OF THE TABS THAT BROKE OFF I JUST PUSHED THEM THROUGH AND CAN TAKE THEM OUT IF I EVER NEED TO REMOVE THE FRONT OF THE DOOR. WORKS FINE AND NO LEAKS. CLEAN THE AREA OF THE OLD GASKET SO THE NEW GASKET WILL HAVE A GOOD SEAL. END OF STORY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerBradley from HEBER CITY UT

Dishwasher was leaking through the door.

All I had to do was take apart the door by removing a few screws. Then ripped the old gasket off. I then lined all the tabs up to make sure it was going to fit and then started pulling them through with needle nose pliers. When the door was reassembled I checked the plastic piece where the gasket ends in the tub and found some loose screws that needed to be tightened. After that I ran a few cycles and it does not leak any more.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerThomas from Beecher IL

The door gasket was leaking

Easy to change. Just pull firmly on old gasket, clean surface with soapy water. Align tabs on new gasket, push into place a tap firmly with handle of a screwdriver and taps pop into place. Was done in about 40 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDanny from Barboursville WV

Water coming out of door bottom

Pull old gasket off (30 seconds), take panel screws out of front panel and control panel, carefully lower control panel push tabs thru holes from inside door, once all tabs in, push door closed and take pliers and pull tabs until they lock into place, put panel back together. not that difficult, my wife and I had it back in working order in approx 30min.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerReavis from Asheville NC

Door gasket cracked

Removed the front of the door by removing 2 screws in each side.

Remove 2 screws on each side holding control panel

Removed old gasket by pulling it out, and installed new gasket. Used needlenose pliers to pull tabs securely into slots.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDonna from Branchville NJ

Original gasket was worn away

I opened the door and pulled the old gasket out using a flathead screwdriver to pry up the difficult to remove areas. I cleaned the area with a damp cloth and place the new gasket in the slots. The entire process including the cleaning took no more than 10 minutes. It was so easy. By the way, I had the part in my hands 2 days after ordering it. I am very impressed with the service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMargaret from Westampton NJ

The door gasket was leaking.

My daughter and son removed the old gasket and installed the new one. It went well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerClaude from malden MI

Water leake bottom left of washer

Removed the seal and replaced with new one. Job went very easy. Stop the leake. Thank you.

Claude Miller

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12