http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/50074.gif
See part 12 in the diagram

Spark Module

PartSelect Number PS2094592

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Gas igniter glows but will not light.
  • Compare At

    $94.25
  • You Save

    $15.71
  • Your Price

    $78.54
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

28 of 42 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

Customerscott from centreville VA

Top burners on stove won't ignite ,no clicking noise

remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMike from Menlo Park CA

Gas range would not light

Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan to complete repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPatrick from Greeneville TN

Range burner igniter not functioning

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 12 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJoseph from East Freetown MA

No spark at top burners

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 7 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customerwilber from oshkosh WI

Terminal spade wrong size on range wiring to fit module

cut off terminals and replaced with the right size one's stove lights every time now wlrowe

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 15 people found this instruction helpful

Parts Used

  • Spark Module

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBronius from College Station TX

Intermittent but rare spark when I went to start the rage: Spark module definitely was toast or on its way out

The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..

Anyhow, thanks to the great part, the stove works really well again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6