2091146-1-S-Whirlpool-77001219-Electronic Range Control
2091146-1-S-Whirlpool-77001219-Electronic Range Control 2091146-2-S-Whirlpool-77001219-Electronic Range Control 2091146-3-S-Whirlpool-77001219-Electronic Range Control

Electronic Range Control

PartSelect Number PS2091146

Overlay not included.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 5 reviews What's this?
1-5 of 5
 

9 of 9 people found this instruction helpful

Parts Used

  • Electronic Range Control

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJeremy from Westmoreland NY

The power had gone out and must have sent a surge that fried the erc. I didn't know that but looked up the "f1" error code that was displayed on the screen online. Once I knew what part to replace it was easy. I just searched out the part on this site and ordered it. I ordered it on a tuesday

First I unplugged the unit. I removed 4 screws to remove the back plate. Removed 4 screws to remove the ERC unit. ( Plastic casing and all) Peeled the front cover off the old unit and stuck it on the new. Removed one wire at a time and plugged it into the new so I didn't mess up the wiring. screwed my 8 screws back in, plugged it in, and started cooking.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Electronic Range Control

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJohn from Manhattan IL

No power to the stove

The repair was easy. I removed the 4 screws to the upper rear cover in the back of oven then unscrewed the 4 screws holding the ERC, Elec Conv-Geneses and undid the 6 color wire conects and the 4 wire plugin. The color wires are labled on diagram and on part. Replaced the divice and reconnected it the same way it in reverse.

However that was not the problem. There was nothing wrong with my ERC, ELEC CONV-GENESIS. I did not check the power to the circuit.
I just figured that it was getting power since the indicator lights were working. One of the 240 circuit
of the circuit breaker was bad (burned out). I turned off the main and replaced the circuit breaker. Works fine now. One learns by there mistakes. Hope this helps...
O by the way I thought I would keep the part just in case I might need it in the future as a backup.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Electronic Range Control

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJustin from Atkins IA

Loss of power, then low power, fried the orginal erc

Remove the 4 screws to the upper rear cover in the back of oven then unscrew the 4 screws holding the ERC, Elec Conv-Geneses and undo the 6 color wire conects and the 4 wire plugin. The color wires are labled on diagram and on part. Replaced the divice and reconnected it the same way it in reverse.

It may help to remove the screws in the lower cover panels on the back of the oven to help reassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Electronic Range Control

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customercassie from leesport PA

Electronic control panel fried

my husband turned off the electric supply, pulled out the stove, took out a couple of screws, put the new part in, and the job was finished

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Electronic Range Control

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerdeborah from Auburn ME

Fi code appeared in the clock area. I called the factory and they told me it was generally the electronic control.

I took the back off the stove and four screws were removed to replace the old unit with the new one. Very easy. I also used the parts diagram from part select to find the part and order it. there follow up for shipping was great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5