2091060-1-M-Whirlpool-77001099-Broil-Element-240V-3000W.jpg
2091060-1-S-Whirlpool-77001099-Broil-Element-240V-3000W.jpg 2091060-2-S-Whirlpool-77001099-Broil-Element-240V-3000W.jpg

Broil Element - 240V 3000W

PartSelect Number PS2091060

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little or no heat when broiling.
  • Cooktop element not heating.
  • Compare At

    $58.69
  • You Save

    $9.78
  • Your Price

    $48.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 4 reviews What's this?
1-4 of 4
 

4 of 4 people found this instruction helpful

Parts Used

  • Broil Element - 240V 3000W

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerFrederick from Snow Hill MD

Broil element broken

First, turn off power to oven. There are six Phillips head screws on the pan above the element and 2 securing the element to the pan. Remove all screws and pull unit toward you, then slide off electrical wires from the element. To remove the element from the pan use the pliers to bend back metal hooks. Place new element under hooks, bending the metal to hold element in place and replace 2 screws securing the element to the pan. Join wires to element and push unit with wiring back into oven wall. Replace 6 screws holding pan to top of oven, turn on power, and voila!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Broil Element - 240V 3000W

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerLaura from Scotts Valley CA

Broiler element broken

FIRST I REMOVED THE SCREWS THAT HOLD THE ELEMENT IN PLACE. THEN I REMOVED THE SCREWS THAT HOLD THE ELEMENT SHIELD ON THE TOP OF OVEN IN PLACE. I THEN PULLED THE ELEMENT OUT OF THE BACK OF THE OVEN ABOUT 3-4 INCHES AND DISCONNECTED THE TWO WIRES. I REMOVED THE WHOLE ASSEMBLY SHIELD AND ELEMENT. THEN I DISCONNECTED THE ELEMENT FROM THE SHIELD LITTLE BRACKETS HOLD IT IN PLACE. TOOK NEW ELEMENT AND FIXED IN PLACE ON THE SHIELD WITH THE BRACKETS. AT THIS POINT I REPLACED THE TWO SCREWS THAT HOLD THE ELEMENT TO OVEN SHIELD. THEN I TOOK THE WHOLE ASSEMBLY AND RECONNECTED THE TWO WIRES. PUSHED THE ELEMENT BACK INTO THE BACK OF THE OVEN. LINED UP THE SCREW HOLES OF OVEN AND BROILER SHIELD PUT SCREWS BACK IN. AND DONE. I MIGHT ADD I TURNED THE POWER OFF TO THE OVEN BEFORE WORKING ON IT.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMarsha from Glen Campbell PA

Broiler element burned out and refrigerator drawer was broken

Replace old crisper drawer. Removed screws from burned out broiler element and plugged in new element. Less than 10 minutes for both jobs. Parts arrived in 2 days. Very pleased and will definitely use partselect again.

Thank you,
Marsha Gardner

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Broil Element - 240V 3000W

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerKevin from Westwood CA

Top broil element no good.

Loosen 6 screws holding pan containing element.Pull element and pan towards the front of oven.Remove the 2 wires attached to element.Remove 2 screws holding element to pan.(Needed WD 40 to loosen screws).Replace in reverse order.So simple this caveman could do it!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4