2089848-1-S-Whirlpool-7432P143-60-Bake Igniter
2089848-1-S-Whirlpool-7432P143-60-Bake Igniter 2089848-2-S-Whirlpool-7432P143-60-Bake Igniter

Bake Igniter

PartSelect Number PS2089848

This part ignites to help bake your food.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Will Not Start.
  • Gas igniter glows, but will not light.
  • Compare At

    $64.58
  • You Save

    $10.76
  • Your Price

    $53.82
In Stock
Order within the next 5 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 6 reviews What's this?
1-6 of 6
 

35 of 40 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerDavid from Temple Terrace FL

Ignitor was bad on upper oven

First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they were fairly easy to get to. 4. I disconnected the ignitor from the back panel then went around to the front of the oven and pulled out the ignitor and all of the attached parts. 5. Here's the tricky part. The screws holding the ignitor in place had fused from the heat and then the threads stripped when I tried to remove them. I had to use a dremel tool and cutting wheel to carefully cut the screws off and then went to buy some replacement screws from the hardware store. 6. I replaced them with a nut and a bolt, to hopefully avoid the same problem for later replacement if necessary. 7. I then replaced everything the same way it came out and all is working like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 20 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerTimothy from Elkhorn WI

Oven would not heat

Lifted door off hinges; removed lower oven spill plate; unmounted bake igniter from heat shield; pulled stove away from wall; removed rear access panels (4 screws); unplugged bake igniter; installed new part; vacuumed behind stove and mopped floor (this took more time than installing the part); oven is back in cookie baking mode!

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerjack from springfield IL

Upper oven would not ignite

removed panel from back 4 screws. unplugged ignitor wire to lower level of upper oven, top wire is for broiler.Slid oven door off its hinges(very heavy)removed wire rack removed 2 screws from bottom pan lifted out,lifted off burner guard, looks like it may have had nuts to hold it down at one time , mine were missing. lifted out burner assembly. removed 2 screws holding down ignitor, they stripped out had to drill holes slightly larger and install new one with screws and nuts I had on hand. Used long screw driver pushed in from behind to guide ignitor wire back thru the insulation. reinstalled everything in reverse and it worked like a new. $50 part part saved us $2000, we were looking at replacing it with a new oven but we really liked what we had. Very satisfied, and wont hesitate to tackle next repair job with help from this web site.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerdave from williams AZ

Replaced igniter

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJames from Keno OR

Upper oven igniter failed

REMOVE DOOR, RACKS, UNPLUG, REMOVE LOWER BURNER COVER TWO SCREWS, THE BURNER TUBE DEFLECTOR PAN TWO WINGNUTS, THE BURNER TUBE. WITH IGNITER ATTACHED, REMOVE BACK OF RANGE 4 SCREWS TO EXPOSE CONNECTOR TO IGNITER, UNPLUG THEN REMOVE BURNER TUBE, THEN IGNITER, REPLACE IGNITER FEED THROUGH BACK OF OVEN WALL AND RECONNECT IGNITER REVERSE PROCESS AND ITS DONE

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 9 people found this instruction helpful

Parts Used

  • Bake Igniter

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerMichael from Minneapolis MN

Oven not reaching proper temperature

Removed old ingniter with screwdriver. Installed new igniter, but had to remove connector in order to electrically connect using twist on connectors.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6