Oven/Clock Membrane Touch Panel

PartSelect Number PS2089486

This part goes in front of the clock/timer to allow visual indication of where the buttons are on the oven. Example bake, broil & clean.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not program.
  • Compare At

    $140.98
  • You Save

    $23.50
  • Your Price

    $117.48
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 12 reviews What's this?
1-5 of 12
 

29 of 31 people found this instruction helpful

Parts Used

  • Oven/Clock Membrane Touch Panel

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJim from La Jolla, CA

Error message is f-1, which is faulty membrane switch

Remove burners and disconnect igniter wires. Remove screws that hold on top of range. Remove screws that hold on front panel. Reach in and disconnect ribbon connector. Front control panel is just stuck on, so gently pry it off. Reverse procedure for new membrane switch. Due to poor engineering, mine goes out every 15-18 months.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 17 people found this instruction helpful

Parts Used

  • Oven/Clock Membrane Touch Panel

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMark from Union, IL

Random f1 alarms

take the 4 screws out, remove the end caps which hold the glass peice on, disconnect the ribbon cable, pry off the old panel, use the razor to clean off the tape/glue, then put it back together.
repair was very easy, took 30 minutes, and it hasn't beeped for over 2 weeks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCharles from Jacksonville, FL

Element bad. Clock membrane touch panel bad.

Remove 2 screws and replce element (turn power off first). Pull old touch panel off and unplug. Plug in new touch panel and stick to front off appliance.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Oven/Clock Membrane Touch Panel

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDon from Waukesha, WI

F1 error code and beeping

Removed 4 screws holding top cover in place.
Took out knobs.
Removed side slides holding panel glass in place
Unplugged Touch panel from ECU
Pulled off old touch panel.
Used WD-40 to remove old adhesive from panel glass
Had to enlarge timer knob hole on new touch panel to fit old knob
Installed new touch panel and plugged back in
Cleaned old greasy areas that were not touched in years (anal retentive action)
Re assembled everything else

6 days and no F1 error or beeping

Very fast shipping from PartSelect.com

Thank You

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Oven/Clock Membrane Touch Panel

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerThomas from Arvada, CO

F-1 warning and beeping

Turn off power ,pull off clock and timer buttom ,lift the light cover , remove a screw on each side of the light, ,than with the stuby screwdriver remove one screw on each side at bottom of front glass, front glass should come loose. peel off the control plate .it is just stuck on the glass front. you will then see where the wire plug go's , unplug the old discard the entire front panel you just peeled of ,,feed new panel wire through the hole and replug it . it only go's one way,peal and stick the control panel., put glass front back ,replace the screws,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 12