BBB A-Plus

Element Infinite Switch - 8"

PartSelect Number PS2089438

This is the left front element switch.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Cooktop element not heating
In Stock

  • Compare At

    $49.48

  • You Save

    $8.25

  • Your Price

    $41.23
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts

Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Infinite Switch - 6"

Part Number 2089437

$41.23
  In Stock

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 NEXT > 1-6 of 6

 

19 of 21 people found this instruction helpful

Parts Used

    • Element Infinite Switch - 8"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDennis from Hagerstown MD

The burner was getting too hot and you could not regular the tempature

Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJames from Chesapeake VA

Could not control burner temp.

removed back cover
removed wires
removed two screws and removed switch
replaced switch and two screws
replaced wires and back cover

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerCarl from Williamsburg OH

Surface element light on when all are off.

I raised the stove top to verify with a volt meter that electricity was truely going to the elements and which ones were receiving current. I removed the back panels to gain access to the controls and wiring. After checking the circuitry with the volt meter I determined that one of the thermostatic controls was defective. I ordered a new control and 8" burner (which showed signs of deterioration) from PartSelect and received them the next afternoon. It took less than an hour to reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

    • Element Infinite Switch - 8"

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerGary from Blanchester OH

Burner heat does not turn down

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerRobert from Santa Fe NM

Installed new switches and elements

just move one wire at a time. Each switch has 5 wires and I am sure mixing them would not be good.

Ordered parts, they shipped same day. Arrived exactly as predicted. Totally non-stress. Can't find a thing to complain about.

Thanks PartSelect

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

    • Element Infinite Switch - 8"

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerSteve from San Luis Obispo CA

Burner control knob/switch shaft had broken off.

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 NEXT > 1-6 of 6