2089437-1-S-Whirlpool-7403P238-60-Infinite Switch - 6"
2089437-1-S-Whirlpool-7403P238-60-Infinite Switch - 6" 2089437-2-S-Whirlpool-7403P238-60-Infinite Switch - 6" 2089437-3-S-Whirlpool-7403P238-60-Infinite Switch - 6"

Infinite Switch - 6"

PartSelect Number PS2089437

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Cooktop element not heating.
  • Compare At

    $46.09
  • You Save

    $7.68
  • Your Price

    $38.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 6 reviews What's this?
1-6 of 6
 

5 of 9 people found this instruction helpful

Parts Used

  • Infinite Switch - 6"

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerdinh from austin TX

One electric burner does not get hot

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

  • Infinite Switch - 6"

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDon from Roanoke VA

Replacement of bad switch

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used

  • Infinite Switch - 6"

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJudy from West Salem IL

Burner would only cook on high setting or not heat up at all.

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerRobert from Santa Fe NM

Installed new switches and elements

just move one wire at a time. Each switch has 5 wires and I am sure mixing them would not be good.

Ordered parts, they shipped same day. Arrived exactly as predicted. Totally non-stress. Can't find a thing to complain about.

Thanks PartSelect

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 11 people found this instruction helpful

Parts Used

  • Infinite Switch - 6"

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerWilliam C. from Sealy TX

6" surface heating coil remained warm when "off"

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • Infinite Switch - 6"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerAaron from Weymouth MA

Power light on, but burner not getting hot

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6