2087906-1-S-Whirlpool-74010546-Door Hinge - Left or Right Side
2087906-1-S-Whirlpool-74010546-Door Hinge - Left or Right Side 2087906-2-S-Whirlpool-74010546-Door Hinge - Left or Right Side http://www.partselect.com/Schematics/Maytag/55501.gif

Door Hinge - Left or Right Side

PartSelect Number PS2087906

This door hinge can be used for the left or right side. As per the manufacture if the hinges have never been replaced,on the appliance,they suggest to replace the door hinge receptacle kit.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door won’t close.
  • Compare At

    $47.35
  • You Save

    $7.89
  • Your Price

    $39.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 8 reviews What's this?
1-5 of 8
 

12 of 22 people found this instruction helpful

Parts Used:
  • Door Hinge - Left or Right Side
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Odin from Warrensburg, MO

Oven door was not closing all the way

First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 16 people found this instruction helpful

Parts Used:
  • Door Hinge - Left or Right Side
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Norman from Brockton, MA

I leaned on the door and broke the hindge

I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used:
  • Door Hinge - Left or Right Side
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Barry from Barre, VT

My wife dropped a cast iron dish on the door while it was open, bent the hinges, so it would not close properly.

It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 10 minutes!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Joseph from San Jose, CA

Door won't close properly

Removed and replace the old spring and it close properly again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Rodney from Knoxville, TN

Replaced faulty door hinge and installed tip-over bracket to floor

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8