2085859-1-S-Whirlpool-74008369-Oven Sensor
2085859-1-S-Whirlpool-74008369-Oven Sensor

Oven Sensor

PartSelect Number PS2085859

This sensor detects the temperature within the oven cavity.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $66.58
  • You Save

    $11.10
  • Your Price

    $55.48
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 3 reviews What's this?
1-3 of 3
 

4 of 5 people found this instruction helpful

Parts Used

  • Oven Sensor

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerAlan from Wallkill NY

Oven temp wrong

Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Oven Sensor

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set

Customerdan from Gallatin TN

Oven had error messages

I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Oven Sensor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerpatrick from Colleyville TX

Sensor went out after fire in oven fault code 1b11

I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3