2085340-1-S-Whirlpool-74007806-Igniter Switch Assembly with Leads
2085340-1-S-Whirlpool-74007806-Igniter Switch Assembly with Leads 2085340-2-S-Whirlpool-74007806-Igniter Switch Assembly with Leads

Igniter Switch Assembly with Leads

PartSelect Number PS2085340

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $60.24
  • You Save

    $10.04
  • Your Price

    $50.20
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 5 reviews What's this?
1-5 of 5
 

6 of 7 people found this instruction helpful

Parts Used

  • Igniter Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Point TX

Electric sparker/ignitor quit working

Remove burner covers (2 screws each)
Unplug hot and neutral leads (spade terminals).
Pull spark units off individual controls.
Attach new spark units to individual controls.
Cut end off hot lead (modification required as new lead came with round terminal instead of spade terminal).
Attach and crimp new spade terminal to hot wire then plug together.
Replace burner covers.
Test for function.
Repair complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Igniter Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerCHRISTOPHER from HOUSTON TX

Water has found its way into the range and shorted the ingnition switch/wire lead assembly and shorted.

I removed the unit from the countertop after turning off and disconnecting the gas. I removed the top panel of the range by removing the burner bases held in place with two torx screws each. Remove the knobs and the whole panel will lift off. After the panel is off the wire lead assembly will just pull off and unplug. The new one is a direct fit. Assemble with the reverse order of disassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Igniter Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerNancy from Lancaster CA

Burner wouldn't light

In cleaning range top with control knobs off, cleaner splashed onto the plastic sandwich containing wires, etc. "spark spark whoosh puff." Turned off electricity, removed sandwich which controled the burner which didn't light and discovered a cooked interior. Going to PartSelect, matched model number, drawing of part, click, order, wait one day. Each burner had to be removed with the star-flower screwdriver, range lid removed. The assembly was a connected set of five. Unsnap old, Insnap new. Easy, peasy. The difficult part was elevating the range tray with one knee to a level where the burners could be screwed back in. It works! New widow, I didn't need directions or physical assistance. Just make certain you have that special little screw driver to remove the burner.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Igniter Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerOcie from Anchorage AK

Ignightor switches needed replacement

replacement harness was an exact replacement except the connector for the supply side. the cook top had a female spade connector and the new harness had a female single pin connector. i had to replace the connector on the harness.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • Igniter Switch Assembly with Leads

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerWilliam from Henderson KY

While cleaning dripped fluid into igniter assembly

I shorted out the igniter assembly snd called a recommended repairman. He came over and called the appliance warehouse he deals with and they quoted him $169.00 for the part with 15 to 20 working days for delivery. He told me it will be a total of $300.00 to repair. After he left I checked on your website and found the part and ordered it. It took 2 days for delivery and was less than $30.00. After reading your simple instructions it took less than 30 min to repair. I took the screws holding the burners off and raised the burner assembly. I removed the old ignitor assembly and installed the new. The lead attachments were different so I cut and spliced the old attachment onto the new. Easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5