Quick Question!

Have you ever purchased from PartSelect.com before?

2085280-1-S-Whirlpool-74007736-Burner Head with Electrode
2085280-1-S-Whirlpool-74007736-Burner Head with Electrode 2085280-2-S-Whirlpool-74007736-Burner Head with Electrode http://www.partselect.com/Schematics/Maytag/59565.gif

Burner Head with Electrode

PartSelect Number PS2085280

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows, but will not light.
  • Will Not Start.
  • Element will not heat.

Compare At

$49.30

You Save

$8.22

Your Price

$41.08
Order within the next 9 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 6 reviews What's this?
1-6 of 6
 

12 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Joe from Saratoga Springs, NY

Electrode would not lite burner

Unscrewed burner head and replaced with new burnerhead and electrode. Just like new. Parts cost 128.00 including shipping. Very simple repair. Saved 200.00 in labor. Parts came within 36 hours. Super Fast.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: bill from spokane valley, WA

Electrode clicked but failed to light burner

I first tried to remove the torx screws only to have them break off..soooo as with most home repairs it grew into a bigger task. 1) unhooked the gas line and unplugged the unit 2) place the unit upside down on workbench 3) used a socket set to remove the hex screws that held the top on 4)removed all the other burners and disconnected electrical wire connected to the igniters. 5) Removed the top 6) uses pliers to remove the screw parts left in the burner base (wd-40 and lock wrench)..Replaced the old gaskets 7) put the top back on and screwed the top back on (make sure you pull the igniter wires through the top before securing it) 8) Reseat and screw in the burners using a torx bit

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: calvin from Edmond, OK

Electrode broke, screw broke

The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Burner Head with Electrode
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: jose from san juan bautista, CA

Erratic spark from electode,gas would no ignate.

Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Burner Head with Electrode
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: W E from Camden, NC

Electrode sparked but not enough to lite burner

Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Mike from Big Canoe, GA

Burner would not light

Replaced burner assembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6