Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2085070
This broil igniter assembly comes with its own metallic mounting bracket and an seven inch long dual wire lead with a plastic plug.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.
My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.
We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!
Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on. At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior. I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.
Replaced gas oven ignitor
Changed the igniter
seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.
I removed the cover protecting the igniter. I pulled the stove away from the wall to get at the connect for the igniter. I loosened the 2 screws which held the igniter. Took the new igniter ran the wire to the back to the connection and mounted the igniter with the 2 screws. Turned on the oven to make sure it works and it did. Turned off the oven, replace the cover and pushed the stove back in place. No big Deal! Your web site was very helpful. Thank you so much!
I was sure my problem was due to a gas ingiter that was no longer working. I read about others that had the same problem as I did. I ordered the part from Partselect because they had a 30 day no hassle parts return policy. I removed the oven racks and 4 screws to get to the igniter.I unpluged the igniter, put the new one in, and replaced the racks. Very simple and easy to do.
First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.
We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.
Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.
Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!
The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.