| |
0 of 1 people found this instruction helpful
Parts Used
-
- Gas Oven Igniter - Vertical Mount
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
Tools
CustomerBeryl from Coventry RI
Oven would not heat/could smell the gas
He took out the bottom of the oven floor...came out easy ..had to unplug the old part and installed the new one the same way.He did have to unscrew two pieces. The only difficult part was reaching to plug in. Not too bad. Now he could do it quick and easier. Problably 10 minutes the most. Stove works great and I can cook again. Makes me happy.Thanks for all your help.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Gas Oven Igniter - Vertical Mount
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerdave from troy ID
Oven would take 3 min. Too lite,would not hold temp,sometimes go up too 350* then down too 250* maybe not relite @ all.
It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!
|
0 of 2 people found this instruction helpful
Parts Used
-
- Gas Oven Igniter - Vertical Mount
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerW from Jonesboro GA
Oven pilot glow only
Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install
|
0 of 2 people found this instruction helpful
Parts Used
-
- Gas Oven Igniter - Vertical Mount
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
Customerbarney from spencerville OH
Oven wouldn't heat up, but igiter turned red hot!
First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!
|
0 of 4 people found this instruction helpful
Parts Used
-
- Gas Oven Igniter - Vertical Mount
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers
CustomerGeorge from Richardson TX
Oven took too long to heat
This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.
|
3 of 14 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerRoland from Poulsbo WA
Oven wouldn,t ignite
first I removed the 2 screws that mount the element. then removed the lower drawer and loosend the screws that hold the shield in place and removed the shield. unpluged the igniter then replaced the igniter. shield back in place and tightened down the element. repair complete. Note don't handle the black portion of the igniter. to replace the oven light simply remove light cover with a flat blade screw driver and pull out the bulb. It couldn't be easier. Do not pay a repairman for these two simple fixes.
|