2084738-1-S-Whirlpool-74007133-Radiant Surface Element - 9"
2084738-1-S-Whirlpool-74007133-Radiant Surface Element - 9" 2084738-2-S-Whirlpool-74007133-Radiant Surface Element - 9"

Radiant Surface Element - 9"

PartSelect Number PS2084738

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.
  • Compare At

    $141.26
  • You Save

    $23.54
  • Your Price

    $117.72
In Stock
Order within the next 35 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 3 reviews What's this?
1-3 of 3
 

3 of 3 people found this instruction helpful

Parts Used

  • Radiant Surface Element - 9"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerGlenn from Arlington Heights IL

Right front burner on my eletric range burnt out.

THE FRONT BURNER THE LARGE ONE WAS BURNT OUT, I COOK ALOT
SO I NEED IT, I HAPPEN TO SEE A APPLIANCE REPAIR MAN NEXT DOOR. I DESCRIBE PROBLEM AND HE SAID WELL FIGURE ABOUT 250 - 300 HUNDRED DOLLARS. 80 FOR THE APRT THE REST LABOR AND HOUSE CALL.WELL I LOOKED AT THE BOOKLET AND FIGURED OUT WHAT I HAD TO DO ,NEEDLESS TO SAY I OWENT TO YOUR WEBSITE AND YOU HAD THE EXACT PART I NEEDED AND SAVED ME ALOT OF MONEY.I SUGEST TO D.I.Yers TRY IT AND IF IT DOESN'T WORK THEN CALL THE REPAIRMAN. THANK YOU PARTS SELECT.
GLENN VOIGHT

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Radiant Surface Element - 9"

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJorge from Richmond CA

Burner not turn on

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Radiant Surface Element - 9"

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerIvan from Grants Pass OR

The right front element (largest) was not working

Remove three screws underneath bottom front edge of the range top. Bewteen the oven door and the range top. Lift rnage top up in frotn and prop up. Remove two screws o the element and replace. Found out the problems was not the element but the control switch. The heating element for the bimetalic control was brokened and not making contact. element was OK. Would advise inspecting and using a DVM to check resistance of the element before purchasiing. By the way I swapped the control switch from another element and found out that they are claibrated to the sixe of the element. You have to purchase the right control switch or the element will not heat correctly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3