Dual Outlet Oven Safety Valve

PartSelect Number PS2084106

This gas oven safety valve is used to make sure that no gas is released until the igniter is ready to ignite. This part is for both the bake and broil igniter in your appliance.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows, but will not light.
  • Little to no heat when baking.
  • Will Not Start.
  • Compare At

    $156.49
  • You Save

    $26.08
  • Your Price

    $130.41
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 6 reviews What's this?
1-6 of 6
 

28 of 33 people found this instruction helpful

Parts Used

  • Dual Outlet Oven Safety Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerEdward from Sewickley PA

Oven would not heat but broiler would.

By undoing the bottom of the stoves back panel, you are able to remove the two knock outs and ben the panel up for complete access. Remove gas line and electrical connection (with stove unplugged and main gas valve turned off). Undo the mounting screws and replace unit following steps in revcerse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 26 people found this instruction helpful

Parts Used

  • Dual Outlet Oven Safety Valve

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerRobert from SALEM IL

Igniter would light----gas valve would not open

SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas
CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Dual Outlet Oven Safety Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerRobert from Hudson OH

Oven would not heat but broiler would

Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wrench. Lift the valve out. Reverse the steps to install the new valve.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Dual Outlet Oven Safety Valve

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerPati from Marietta GA

Oven wouldn't heat, broiler would.

Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Wrench set

CustomerMichael from San Diego CA

The burners inside the oven would not light

Pulled Oven from wall, disconnected gas and electric, removed bottom drawer, laid oven on its back, removed dual outlet valve ( tight space to loosen fittings, had to remove burner in oven to replace valve.) installed new valve, put teflon tape on all screw joints and tightened, Removed old Oven igniter and installed new igniter while burner was removed during the step above, reconnected all wires, connected gas, plugged in oven, pushed back into place, releveled range, Oven works great. Time does not include cleaning of range and area underneath, repainting the range top. I cleaned the range top burners also and they light much quicker now

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

  • Dual Outlet Oven Safety Valve

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerLarry from Montgomery TX

No problem at all

Pulled stove away from wall to access gas valve in rear. Adjusted the jet on the replacement valve for LP gas and connected the four control wires. Two open end wrenches and one stubby phillips screwdriver were all that was needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6