2081226-1-S-Whirlpool-74003019-Bake Element
2081226-1-S-Whirlpool-74003019-Bake Element 2081226-2-S-Whirlpool-74003019-Bake Element 2081226-3-S-Whirlpool-74003019-Bake Element http://www.partselect.com/Schematics/Maytag/42163.gif

Bake Element

PartSelect Number PS2081226

This oven bake element with push-on terminals has a terminal depth of three inches. It is found on the bottom of the oven.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Oven is too hot.
  • Will Not Start.
  • Compare At

    $25.08
  • You Save

    $4.18
  • Your Price

    $20.90
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 131 reviews What's this?
 

4 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: richard from Inwood, NY

The bake element broke at the rear causing a minor electric flash inside the oven

You guys had a installation video which help greatly. I did run into a couple issues. Firstly, it didn't see a plug for the oven so I shut the power down from the panel. Lastly, disconnecting the old bake element from the electric insert at the ends was a bit challenging. The element and the inserts looks as if it was one piece but eventually it pulled apart. Installing the new piece was very easy. You want to consider adding additional legs under the bake element closet the area where the element connect to the oven inserts. When my old element broke and failed, the live piece can in contact with the floor of the oven causing a flash. It was a bit scary.

Thank you very much for your expeditious shipment and your follow up. Great job!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: dennis from willards, MD

Bake element would not heat

unpluged unit took out bake element tested element with VOM,reading showed element to be ok. reinstalled element took back off the stove to expose the timer control for inspection and found the High voltage switch points on the bake control to be burnt off.ordered new timer control reversed the dismanteling process to install.my color code on the wiring was different,but I knew white is always nuetral,and black or red can be line,my yellow was bake which was the same in the diagram so my blue for broil had to be purple shown in the diagram.just a shame you can't buy the bake switch separate. Everything is working great !

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: John from Foxboro, MA

Bake element wouldn't heat up to temperature

I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wire and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Stephen from Pleasant Hill, IA

Baking element burned out

I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Dan from TomRriver, NJ

Bake element caught on fire

I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?