2080608-1-S-Whirlpool-74001870-Electronic Relay Board
2080608-1-S-Whirlpool-74001870-Electronic Relay Board 2080608-2-S-Whirlpool-74001870-Electronic Relay Board 2080608-3-S-Whirlpool-74001870-Electronic Relay Board

Electronic Relay Board

PartSelect Number PS2080608

This board sends information (such as temperature of oven, bake, broil) to the main control board during specific functions.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $207.86
  • You Save

    $34.64
  • Your Price

    $173.22
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 3 reviews What's this?
1-3 of 3
 

9 of 11 people found this instruction helpful

Parts Used

  • Electronic Relay Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerS Gregory from New Braunfels TX

Timer controller (clock & controls) not working/lighting up

Simple. Just take off Ceran cook top, I used my iPhone to take a picture of the electronic relay board I was replacing just in case I need a reference picture. With circuit breaker turned off, I removed one connection at a time from the old board and plugged into new board (a total of 7 connections), popped the old board out, popped the new board in, no screw driver needed for this part--just for replacing the ground wire on the Ceran cook top. Reassembled top and flipped the breaker. Works like new!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerTom from Independence MO

Display goes blank,press display it comes back

Display goes blank, had to press hard to get back, other times oven would shut off display flash. again pressing display cleared problem. Replaced display, problem came back but not as bad and only had to press lightly to get back. I then replace relay board & sensor. No more problems. Again, turn pwr off, remove burners & reflectors, mark burner receptacles as to FR-RR-LF-LR, Philips screw driver remove these, pop top, lay wiring forward, remove 4 Philip screws holding cover, angle one side down and pull up other side. should be enough wire to pull from relay board and place on new one, then use needle nose or regular pliers to pinch stand offs so board comes up. Remove two plastic legs, (might be brittle) put on new board, press board down on stand offs. Sensor is obvious. Replace covers, and other items and your done. Nothing really to hard.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

  • Electronic Relay Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJanie from McHenry IL

I couldn't shut off my oven oven just kept getting hotter and hotter the only way to shut it off was to simply pull the plug..it is an electric oven/range

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the original and simply connected the new one. screw it all back together. Turned the electric back on and I was ready to cook for our Thanksgiving dinner

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3