| |
26 of 31 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
Customergeorge from burke AL
Wanted to update surface parts to a very old (27 yrs?) jenn-air range on an island
The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.
|
13 of 19 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:15 - 30 mins
Tools
CustomerLucille from Mattoon IL
Wanted to "renew" cook top
The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.
|
6 of 7 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers, Wrench set
Customeranne from richwood KY
The original equipment fan switch failed
The part we received from your supply store, a Maytag part, was in no way a direct replacement for the original Jenn-Air switch. I had to shave material carefully off all sides of the supplied switch, including the plastic flanges that were to hold the switch in place. Consequently, there was nothing left to hold the shaved-down switch in the opening. I had to rig two pieces of material to attach to the back of the switch to hold the switch, roughly, in place.
So, a poorly fitting replacement part that happens to function acceptably after an hour's work.
The repair: The balance of the repair was unremarkable. I simply removed the metal plate that the control knobs are mounted on, pulled it out of the rangetop, and removed the old switch. I snipped the wires, as your instructions said, nutting off the ground wire which is not used. I used a compression tool to attach the two wires to the quick-connect connectors you supplied (many home repair folks would not have a crimp tool for this job). The rest of the time was spent reshaping the switch you sent to fit into the too-small mounting hole.
I then simply returned the switch mounting plate, fastened with screws, to the range top.
|
6 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMary Jo from Minford OH
The drip bowls were old and stained; the knobs were so worn that they could hardly be read.
OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.
|
6 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from San Antonio TX
New drip bowls
I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMargaret from Kingwood TX
Small burner only heated intermittently.
Unplugged old burner element, plugged in new element.
|
4 of 7 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsScrew drivers
CustomerAlbert from Snellville GA
Connector for burner broke old and well used
Had to drill out screw for old connector bracket and also had to extend wires from controls this took most time. Once done with this used wire cutters to strip back insulation and then put the whole mess back together also used a larger wire nut to reconnect wires.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerErin from Coeur D Alene ID
Missing drip bowls
Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!
|
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from Richardson TX
Old, crusty drip pans
This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWarren E from Newport VT
Install burner drip pans
Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerMichael from Penryn CA
Burned out receptacle
Searched for parts and found PartsSelect to substantially underprice Sears for same items. removed old recept. with a screwdriver, no problem, had a little difficulty getting new wires attached as hand wouldn't fit under burner area and the wires were short. Also the recept. bracket screw hole was a little tight for the screw so I had to "stretch" it out a bit. Replacing drip pans and rings was a simple change out of the old, no tools needed for that. Overall an easy job.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerStarla from Carrollton TX
Drip bowls were rusted, element was broken
All I did was take out the old drip bowls and broken element and put in the new. I have had a difficult time trying to find the parts, but PartSelect made it so easy and the parts were the correct ones for my old JennAir stove.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerChhristopher from Houston TX
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
CustomerVeronica from East Sandwich MA
Burner not wrking well and did not fit well anymore. The whole burner was slippig when cooking withit.
Took out the old element, ring and drip and replaced with new.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerAlfred from Fayetteville NC
Old stove drip bowls needed replacing
Removed heating elements and dropped new drip bowls in and replaced new elements
|