2078472-1-S-Whirlpool-71003424-Electronic Clock Control Board
2078472-1-S-Whirlpool-71003424-Electronic Clock Control Board 2078472-2-S-Whirlpool-71003424-Electronic Clock Control Board 2078472-3-S-Whirlpool-71003424-Electronic Clock Control Board

Electronic Clock Control Board

PartSelect Number PS2078472

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not program.
  • Compare At

    $337.46
  • You Save

    $56.24
  • Your Price

    $281.22
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 51 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerGeorge from Wilmington DE

Led clock faded then black,oven worked but no clock

First: my problem was with the oven. Turn power off at breaker,should be one of the largest breakers, 30 or 40 amp. type.Then open door look up under LED readout you will see 4 phillip head screws, remove them,then lift LED section upward and off.You may want/need someone to hold this section.Then unplug the wires by pulling firmly upward and off of the LED plastic box. The box is held on by 4 hex nut screws, unscrew and remove box,install new LED display in reverse order. turn power back on.Set clock. Your done.Sounds like a long project but I actually had two ovens to do.Total time for the first oven was 12 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerCarol from Kilgore TX

Time light dimmed and then no longer seen

First I had to remove the cover for the oven because my appliance is an oven/microwave combination. Then I just followed the directions of the people on site and it worked like a charm!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWilliam from Hayden Lake ID

The clock digets on the control panel faded away

I removed the four screws that hold the control panel in place, unpluged the three wire connectors, and removed the clock assembly by removing four screws that hold it in place. Next I replaced the four screws that hold the clock in place, pluged in the wire connectors, and replaced the control panel. It was a very simple task.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerWallace from Mason City IA

Digital readout went very dim

Open oven door, remove four phillips screws, lift off the faceplate. Remove circiut board containing the readouts with nutdriver unplug two connectors and install the new board. Very happy with results and saved a bundle !!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerKeith from Petaluma CA

Led light on over temp gave up &died

I removed the front cover piece and looked at what I was going to replace and then put it back in place. I went on line and got the part from the manufacture, not returnable if I screw up and get the wrong part. Ordered and recieved-right one. I removed the front cover snaped in the electrical tested to make sure it worked, it did. 4 screws back together and it is working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerPatrick from Carmel IN

The timer/clock on the oven display was out.

Turned off power to the oven. Removed the four screws on the bottom of the control panel. The panel then needed to be lifted up just a bit to release from a bracket that holds the top in place. Because this is a built-in with a microwave oven above it I had to remove four screws to take off the decorative facade from around the microwave.

Once the surround on the microwave was removed I slide up the control panel. Removed 3 cables from the timer and the 4 screws holding it in place. Installed the new timer (4 screws and 3 cables), put the control panel back in place. Four screws in the bottom of the panel, four screws in the surround and done. Turned the power back on to the oven and 2 days later cooked a turkey for Thanksgiving.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerTerry from Grand Prairie TX

Needed to replace the clock assembly

Repair was just exactly like a dozen I read before I ordered the part. Turn off breaker. Remove 4 phillips head screws on the bottom of the clock face. Tilt out from the bottom, take out 4 screws with 1/4" nutdriver, unplug 3 wiring harnesses. Replace in reverse order and turn the power back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerJeffery from Seguin TX

Jenn-air oven electronic display ceased working

Number one: trip the breaker on the oven. Next, I removed four screws from the bottom of the front display panel. Then, unhooked the panel and gently placed it on the counter next to it. Then I un-plugged each of the three inputs and plugged them into the new component. I then unscrewed the four hex screws from assembly and removed the old unit. I reversed the process and screwed it back in, and when I turned on the circuit breaker, everything worked as advertised. Total time: less than 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGary from Lake Lure NC

Oven clock was real dim.

First I removed the four screws from the control panel. This was done by opening the oven door. Lifted up on the control panel and removed it. Then unplulged the three conecters to the control board. Removed the four screws holding the board in place. Put the new board in, connected three plugs, put the control panel back on and attached it with the four screws from under neath.Simple!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerBob from Castle Rock CO

Clock & temp display fadded out

After reading how the others did this repair, I told Nancy, no sweat, you can do it. We removed the four screws from under the panal, removed the panal, unpluged the wire leads and laid the unit on a towel. We then removed the four nuts that held the clock assembly and exchanged the old for the new. Reversed the proceedure and it worked. Don't forget to turn the power off before the repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWilliam from Morgan Hill CA

The clock assy led was so dim I could not see it.

I removed 4 screws on the under side of the glass that held the clock assy. removed the glass panel and removed 3 connectors off the back. Removed the 4 screws holding down the clock assy with a nut driver. Put the new part in place and it was back together in 3 min. Easy Peezy I would of felt foolish hireing a repairman to do this job....

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDouglas from Nesconset NY

Clock/light display dim or off

shut power off to wall oven,open oven door & with phillips screw driver remove 4 screws. lift clock display up & out,unplug three harness's & remove.unscrew the four 5/16 bolts and remove and replace the light display.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerBarbara from Port Charlotte FL

Oven clock display out

Remove 4 screws above oven door. Lift glass clock display from oven. Remove four nuts, unplug 3 connectors, lift module out. Install new module, reverse removal procedure. Shazam! Like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMichael from Lakewood CO

The display went dim and then out. Common problem - most in development have had to do- design flaw.

Open oven, Remove the 4 screws located on top leading edge of the oven. Pull the plugs from the pannel and then using the nut driver remove screws. Reattach plugs- note do not force. Two people- one to hold the pannel while you do change out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 7 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Albuquerque NM

Timer display on wall oven/microwave getting dim

Removed the four screws that hold the oven assembly in the cabinet, slid it part way out and let the front edge rest on the kitchen stool (these puppies are heavy!)

Removed bezel from around the microwave, removed screws that hold the microwave in, and slid it out.

removed the microwave tracks, and removed the top panel from the oven.

remove four screws that hold the timer to the front panel, unplugged three connectors, and remove timer.

Plug the three connectors back in; watch out, the pins bend easily!

Re-install the four screws; the top two are hard to see. A magnet on the nutdriver helps.

Re-install top panel, microwave tracks.

slide the microwave in, re-install bezel.

Heave the whole thing back into the cabinet, and shim to level; important step! otherwise the door won't close right.

Re-install the four screws that keep it in the cabinet. Not needed for strength, just in case gravity decides to stop operating.

Important; don't forget to cut off power before removing, don't forget to plug the microwave back in (ask me how I know) or you'll be pulling it out again.

Easy job except for two invisible screws, heavy components, and sharp-edged sheet metal. Probably saved more than $200 on service charges, between saving on parts and labor.

Help other customers find the most helpful instructions.

Were these instructions helpful?