2078453-1-S-Whirlpool-71003401-Electronic Clock Control Board
2078453-1-S-Whirlpool-71003401-Electronic Clock Control Board 2078453-2-S-Whirlpool-71003401-Electronic Clock Control Board 2078453-3-S-Whirlpool-71003401-Electronic Clock Control Board http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/52303.gif

Electronic Clock Control Board

PartSelect Number PS2078453

This electronic board is located within the control panel.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $446.51
  • You Save

    $74.42
  • Your Price

    $372.09
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.8 / 5.0, 30 reviews What's this?
1-5 of 30
 

20 of 22 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRollin from Petaluma, CA

Dim clock and oven display lights

Turn off power to oven. open top oven door and remove the four screws holding the display unit in place. Pull out on the bottom and lift up. Disconnect the wires and lay unit on counter.
Remove the four screws holding the clock display and replace with new part. Reassmble. Ahhh lights. Pray that you new unit doesn't burn out in four years. The end.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 11 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerGorden from Silver Spring, MD

Led lights faded and eventually disappeared

First, I turned off the circuit breaker to the double over.
Second, I opened the oven door. At the top of the frame, underneath the panel are four screws (not evenly spaced) that I removed. I held onto the glass control panel, not wanting it to come down when I removed the screws, but this was unnecessary as there is a ridge in the back to keep it in place.
Third, I lifted out the glass control panel. There are two sets of wires going from the oven to the control panel. One set of wire connects in two places (three connections in total).
Fourth, I simply disconnected these wires from the chips (lifting them off), trivial. They all have different connectors, so there is no chance of getting them mixed up. If you have never touched any new electronics and are completely unfamiliar with plugging wires on a chip, you may take note of the orientations of the connectors), but it is fairly dummy-proof.
Fifth, there are four screws holding the display in place. Used the socket wrench for these (they go through the holes you see on the side of the unit in the picture).
Sixth, reversed the last operation, screwing the new display in place on the removed panel.
Seventh, Some of the teeth on the connector of my new display were bent over. I bent these straight so the connector would go over them, and reconnected the wires, carefully(!)
Eighth, slipped the glass panel in place. When seated properly, it does not shift.
Ninth, secured panel with the four initial screws.
Tenth, turned on the circuit breaker.
Eleventh, was shocked by how bright the new LED was!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerTom from Elba, AL

Electronic display was too dim to read and the top baking element was burned out.

I removed two screws to take the control panel off.
The electronic display is held in place with four screws which are easily removed with a nut driver.
The wiring work is extremely simple.
To replace the element, I removed the oven racks, took two screws out, disconnected the two wires, then replaced the element by reversing the process.
Both jobs took less than 20 minutes and that includes two trips to the breaker box in the basement.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerChristopher from Downingtown, PA

The over display was getting dimmer and dimmer, could not see the clock.

First, I searched ythe partselect.com web site for "Dim over display for Jenn-Air double over" and found an answer to some one with the exact same model as me. The answer said to order the "clock assembly" and all would be solved.

So, I ordered the assembly, it arrived. First thing I did was turn off the circut breaker for the over! I removed 4 screws holding the oven display in place. With those 4 screws removed, I was able to remove the clock assembly with 4 more screws and 3 cable connecters.

Put the new assembly in place, hooked up the connectors and turned the circut breaker back on. Everything was done and working within 15 minutes! Could not have been easier, it's great to have the display back again, we can now tell the oven temp, how much time is left on the timer, etc!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDawn from Muscatine, IA

Lcd display was no longer visible without lights out

Turned off power to range - Removed the 4 screws holding the glass assembly in (front glass touch panel on range). and lifted up to expose wiring and electrical components. Pulled off all electrical plugs (4) and detached clock component from assembly by unscrewing 4 screws. Replaced new assembly, secured with 4 screws, plugged in all 4 plugs - turned circuit breaker on to restore power - WaLah!! That SIMPLE!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 30